Ana içeriğe geç
İngilizce
Japonca
Adım 2
To ensure a good adhesive bond, thoroughly clean the adhesion surfaces. This may take some time, but the results are worth the effort. Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or tweezers. Do not use metal tools if you are cleaning display panels or glass covers, as the tools may scratch the surface.
Prepare the surface
  • To ensure a good adhesive bond, thoroughly clean the adhesion surfaces. This may take some time, but the results are worth the effort.

  • Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or tweezers.

  • Do not use metal tools if you are cleaning display panels or glass covers, as the tools may scratch the surface.

  • Use adhesive remover or isopropyl alcohol (>70%) to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.

  • While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning.

  • Allow the alcohol to completely evaporate from the device before re-assembly.

しっかりと接着剤を装着するには、表面を完全に綺麗な状態にする必要があります。この作業には時間がかかるかもしれませんが、それだけ結果につながります。

指やスパッジャー、プラスチックの開口ツールもしくはピンセットを使って、古い接着剤の塊を取り除きます。

ディスプレイパネルもしくはガラスカバーをクリーニングする場合、ツールが表面を傷つけてしまう恐れがあるため、メタル製ツールは使用しないでください。

ディスプレイパネルもしくは90%以上の高濃度イソプロピルアルコールを使って、メタル表面に残っている接着剤を取り除きます。糸くずのでないマジッククロスやコーヒーフィルター等で一方方向に向けてワイプします。

イソプロピルアルコールは、電子製品に使用しても安全ですが、あるフォーム製接着剤を溶解することがあります。クリーニング中は、アルコール成分が含まれているか確認してください。デバイスを再組み立てする前に、アルコールを完全に蒸発させてください。

[title] Prepare the surface
[* icon_note] To ensure a good adhesive bond, thoroughly clean the adhesion surfaces. This may take some time, but the results are worth the effort.
[* black] Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or tweezers.
[* icon_caution] Do not use metal tools if you are cleaning display panels or glass covers, as the tools may scratch the surface.
-[* black] Use adhesive remover or high concentration (>90%) isopropyl alcohol to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.
- [* icon_note] While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning, and allow it to completely evaporate from the device before re-assembly.
+[* black] Use adhesive remover or isopropyl alcohol (>70%) to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.
+ [* icon_note] While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning.
+ [* icon_note] Allow the alcohol to completely evaporate from the device before re-assembly.

Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.