Eşyalarını Tamir Et Topluluk Mağaza

Google Pixel 4a 스크린 교체하기

Uyarı: Ön koşul olan bir kılavuzu düzenliyorsunuz. Yapacağınız herhangi bir değişiklik bu adımın yer aldığı bütün 11 kılavuzları etkileyecektir.

Kılavuza Dön
İngilizce
Korece
Adım 6
Google Pixel 4a Screen Replacement: adım 0, 3 resimden 1. Google Pixel 4a Screen Replacement: adım 0, 3 resimden 2. Google Pixel 4a Screen Replacement: adım 0, 3 resimden 3.

  • The screen adhesive is very weak and you should not need to re-apply heat. If the screen does feel hard to slice, apply heat to the difficult area for one minute and try again.

  • Insert another opening pick into the right edge of the phone at an angle where a gap has already formed to prevent damage to the OLED panel.

  • Slide the opening pick around the bottom of the phone to cut the adhesive.

  • There is a delicate cable under the bottom-right corner of the screen. If you feel your opening pick snag on anything, pull it out and try again. Make sure your pick is angled downward and only inserted as little as is necessary to separate the adhesive (no more than 2 mm deep).

  • Leave the pick inserted along the bottom edge to prevent the adhesive from resealing.

스크린 접착제는 매우 약하므로 열을 다시 가할 필요가 없습니다. 스크린을 자르기가 어렵게 느껴지면 어려운 부분에 1분 동안 열을 가한 후 다시 시도하세요.

OLED 패널이 손상되지 않도록 이미 틈이 생긴 각도로 휴대폰의 오른편 가장자리에 다른 여는 픽을 끼우세요.

여는 픽을 휴대폰 하단 주위에서 밀어 접착제를 자르세요.

스크린 오른편 하단 모서리 밑에 연약한 케이블이 있습니다. 여는 픽이 무언가에 걸리는 느낌이 들면 픽을 빼고 다시 시도하세요. 픽이 아래쪽으로 기울어져 있고 접착제를 분리하는 데 필요한 만큼만 끼워져있는지 확인하세요 (3mm 깊이 이하).

접착제가 다시 붙지 않도록 픽을 하단 가장자리를 따라 끼운 채로 두세요.

[* icon_note] The screen adhesive is very weak and you should not need to re-apply heat. If the screen does feel hard to slice, apply heat to the difficult area for one minute and try again.
[* black] Insert another opening pick into the right edge of the phone at an angle where a gap has already formed to prevent damage to the OLED panel.
[* black] Slide the opening pick around the bottom of the phone to cut the adhesive.
- [* icon_caution] There is a delicate cable under the bottom-right corner of the screen. If you feel your opening pick snag on anything, pull it out and try again. Make sure your pick is angled downward and only inserted as little as is necessary to separate the adhesive (no more than 3 mm deep).
+ [* icon_caution] There is a delicate cable under the bottom-right corner of the screen. If you feel your opening pick snag on anything, pull it out and try again. Make sure your pick is angled downward and only inserted as little as is necessary to separate the adhesive (no more than 2 mm deep).
[* black] Leave the pick inserted along the bottom edge to prevent the adhesive from resealing.

Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.