Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

İngilizce
Fransızca

Remplacement du connecteur de charge Lightning et de la prise Jack de l'iPhone 6s Plus

Kılavuz Bilgisi

= Bitti = Eksik
    Follow the steps in this guide to replace the lower flex cable in an iPhone 6s Plus. This cable assembly is home to the headphone jack and Lightning connector. If your phone is having trouble charging or connecting via USB, or you have a loose headphone jack, replacing this component can resolve your issue. [ … ] Note that it's possible to replace this component while leaving the logic board installed, by skipping steps 22-37, 40-49, and 53. Then in step 56, instead of removing the speaker, you must either carefully move it out of the way, or detach it from the black antenna cables so you can remove it. Afterward, when removing the Lightning connector assembly, you must be extra careful not to pry against the logic board or battery. This approach leaves you less room to work, but eliminates a lot of steps. [ ] YouYou can also use this guide to replace the '''[https://www.ifixit.com/Guide/iPhone+6s+Plus+Lightning+Connector+and+Headphone+Jack+Replacement/54171#s119184| lightning connector bracket]'''. bracket.
    Follow the steps in this guide to replace the lower flex cable in an iPhone 6s Plus. This cable assembly is home to the headphone jack and Lightning connector. If your phone is having trouble charging or connecting via USB, or you have a loose headphone jack, replacing this component can resolve your issue. [ … ] Note that it's possible to replace this component while leaving the logic board installed, by skipping steps 22-37, 40-49, and 53. Then in step 56, instead of removing the speaker, you must either carefully move it out of the way, or detach it from the black antenna cables so you can remove it. Afterward, when removing the Lightning connector assembly, you must be extra careful not to pry against the logic board or battery. This approach leaves you less room to work, but eliminates a lot of steps. [ ] YouYou can also use this guide to replace the '''[https://www.ifixit.com/Guide/iPhone+6s+Plus+Lightning+Connector+and+Headphone+Jack+Replacement/54171#s119184| lightning connector bracket]'''. bracket.
      ToCompare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing. [ ] '''To reassemble your device, follow these instructions in reverse order. order.''' [ ] Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]]. [ ] Repair didn’t go as planned? Check out our [https://www.ifixit.com/Answers/Device/iPhone%206s%20Plus|iPhone 6s Plus Answers community] for troubleshooting help.
      ToCompare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing. [ ] '''To reassemble your device, follow these instructions in reverse order. order.''' [ ] Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]]. [ ] Repair didn’t go as planned? Check out our [https://www.ifixit.com/Answers/Device/iPhone%206s%20Plus|iPhone 6s Plus Answers community] for troubleshooting help.

      Üzerinde çalıştığınız device'ın spesifik parçasını veya bileşenini tarif edin. EÖrneğin: Pil

      Bir başlık oluştur.

      Bu 1-2 cümlelik özet, arama sonuçlarında görüntülenecektir.

      Okuyucuya, onlar daha kılavuza dalmadan önce gerekli olan arka plan bilgilerini aktarın.

      Kılavuz Adımları

      Adım 1

      À l'aide de l'extrémité pointue d'une spatule, déconnectez la nappe du Taptic Engine de la nappe inférieure.

      Adım 2

      Retirez les vis suivantes, maintenant le Taptic Engine en place :

      Adım 3

      Décollez le morceau de bande adhésive, qui recouvre la vis fixant la nappe du connecteur de charge au rebord du téléphone.

      Adım 4

      Dévissez les cinq vis cruciformes suivantes :

      Adım 5

      Préparez un iOpener et posez-le sur le bas de votre téléphone pour faire ramollir l'adhésif maintenant la nappe du connecteur de charge Lightning en place.

      Adım 6

      Insérez un médiator entre le support de mise à terre supérieur droit de la nappe et la coque arrière et commencez à les séparer.

      Adım 7

      Continuez à le faire glisser sous la nappe.

      Adım 8

      Avec un médiator, faites levier sur le microphone gauche pour le séparer du bord de la coque arrière.

      Adım 9

      Répétez l'étape précédente pour le microphone inférieur droit.

      Adım 10

      Avec l'extrémité pointue d'une spatule (spudger), poussez la prise Jack de 3,5 mm hors de son emplacement dans la coque arrière.

      Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.