Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

İngilizce
İtalyanca

Connettore Lightning e jack cuffie iPhone 6s Plus

Kılavuz Bilgisi

= Bitti = Eksik
    Follow the steps in this guide to replace the lower flex cable in an iPhone 6s Plus. This cable assembly is home to the headphone jack and Lightning connector. If your phone is having trouble charging or connecting via USB, or you have a loose headphone jack, replacing this component can resolve your issue. [ … ] Note that it's possible to replace this component while leaving the logic board installed, by skipping steps 22-37, 40-49, and 53. Then in step 56, instead of removing the speaker, you must either carefully move it out of the way, or detach it from the black antenna cables so you can remove it. Afterward, when removing the Lightning connector assembly, you must be extra careful not to pry against the logic board or battery. This approach leaves you less room to work, but eliminates a lot of steps. [ ] YouYou can also use this guide to replace the '''[https://www.ifixit.com/Guide/iPhone+6s+Plus+Lightning+Connector+and+Headphone+Jack+Replacement/54171#s119184| lightning connector bracket]'''. bracket.
    Follow the steps in this guide to replace the lower flex cable in an iPhone 6s Plus. This cable assembly is home to the headphone jack and Lightning connector. If your phone is having trouble charging or connecting via USB, or you have a loose headphone jack, replacing this component can resolve your issue. [ … ] Note that it's possible to replace this component while leaving the logic board installed, by skipping steps 22-37, 40-49, and 53. Then in step 56, instead of removing the speaker, you must either carefully move it out of the way, or detach it from the black antenna cables so you can remove it. Afterward, when removing the Lightning connector assembly, you must be extra careful not to pry against the logic board or battery. This approach leaves you less room to work, but eliminates a lot of steps. [ ] YouYou can also use this guide to replace the '''[https://www.ifixit.com/Guide/iPhone+6s+Plus+Lightning+Connector+and+Headphone+Jack+Replacement/54171#s119184| lightning connector bracket]'''. bracket.
      ToCompare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing. [ ] '''To reassemble your device, follow these instructions in reverse order. order.''' [ ] Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]]. [ ] Repair didn’t go as planned? Check out our [https://www.ifixit.com/Answers/Device/iPhone%206s%20Plus|iPhone 6s Plus Answers community] for troubleshooting help.
      ToCompare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing. [ ] '''To reassemble your device, follow these instructions in reverse order. order.''' [ ] Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]]. [ ] Repair didn’t go as planned? Check out our [https://www.ifixit.com/Answers/Device/iPhone%206s%20Plus|iPhone 6s Plus Answers community] for troubleshooting help.

      Üzerinde çalıştığınız device'ın spesifik parçasını veya bileşenini tarif edin. EÖrneğin: Pil

      Bir başlık oluştur.

      Bu 1-2 cümlelik özet, arama sonuçlarında görüntülenecektir.

      Okuyucuya, onlar daha kılavuza dalmadan önce gerekli olan arka plan bilgilerini aktarın.

      Kılavuz Adımları

      Adım 1

      Usa l'estremità punta di uno spudger per scollegare il cavo flessibile del Taptic Engine dal cavo flessibile inferiore.

      Adım 2

      Rimuovi le seguenti viti a croce Phillips che tengono in posizione il Taptic Engine:

      Adım 3

      Stacca il nastro adesivo disposto sopra la vite che fissa il cavo flessibile del connettore Lightning al bordo del telefono.

      Adım 4

      Stacca le seguenti cinque viti a croce:

      Adım 5

      Prepara un iOpener e disponilo sulla parte inferiore del telefono per ammorbidire l'adesivo che tiene in posizione il cavo flessibile del connettore Lightning.

      Adım 6

      Inserisci un plettro di apertura tra la staffa di terra superiore destra del cavo flessibile e il case posteriore per iniziare a separare le due parti.

      Adım 7

      Continua a far scorrere il plettro di apertura sotto il cavo flessibile.

      Adım 8

      Usa un plettro di apertura per staccare il microfono di sinistra dal bordo del case posteriore.

      Adım 9

      Ripeti il passo precedente per il microfono inferiore destro.

      Adım 10

      Usa l'estremità a punta di uno spudger per far saltare via il jack cuffie dal suo alloggiamento nel case posteriore.

      Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.