Eşyalarını Tamir Et Topluluk Mağaza

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

Breville 860 Grinder Teardown

Neye ihtiyacın var

    • I grab this video from Youtube, its show very clear how to open the top and the back panel. Please watch until 2min

    Düzenle

  2. Breville 860 Grinder Teardown, Cut the lines connect to motors: adım 2, 2 resimden 1. Breville 860 Grinder Teardown, Cut the lines connect to motors: adım 2, 2 resimden 2.

    • Unscrew the white box cover in the back, 4 screws.

    • Remove the white box cover, and then careful lift the electronic board as the picture

    • Look for two line, one white and one black on the bottom. They should be connect to the electronic board through 2 connectors

    • Cut that two lines

    Düzenle

  4. Breville 860 Grinder Teardown, Take the motor out: adım 3, 2 resimden 1. Breville 860 Grinder Teardown, Take the motor out: adım 3, 2 resimden 2.

    • Unscrew and take out the dial

    • Take out the outer burr

    • Unscrew 4 screws

    • Take out the motor

    Düzenle

  5. Breville 860 Grinder Teardown, Open the cover of the gear: adım 4, 2 resimden 1. Breville 860 Grinder Teardown, Open the cover of the gear: adım 4, 2 resimden 2.

    • Unscrew 4 screws

    • Carefull lift the part with motor up.

    Düzenle

  6. Breville 860 Grinder Teardown, Examine the gear: adım 5, 3 resimden 1. Breville 860 Grinder Teardown, Examine the gear: adım 5, 3 resimden 2. Breville 860 Grinder Teardown, Examine the gear: adım 5, 3 resimden 3.

    • Examine the gear.

    • In my case, I found one strange object, sticked on the gear wall. Look like it is a washer pressed with gear teethes. Good to take it out but I wonder where it came from?

    Düzenle

  7. Breville 860 Grinder Teardown, Open the limiter: adım 6, 3 resimden 1. Breville 860 Grinder Teardown, Open the limiter: adım 6, 3 resimden 2. Breville 860 Grinder Teardown, Open the limiter: adım 6, 3 resimden 3.

    • Unscrew this, remember follow the clock wise

    • If you just want to replace worn out impeller: hold the limiter steady, unscrew (red square) with clock wise, take out the inner burr. And try to clean and replace the impeller while holding the limiter! You should ask some body to help with this step.

    • Take the Limiter out. Take care because it go with 6 balls and 6 springs! Perform this step only if you think there are some wrong with the Limiter (Big crack sound when grind )

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

10 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

thanhlp

Üyelik tarihi: 07/11/18

410 İtibar

1 Kılavuz yazıldı

Rozetler: 9

+6 tane daha rozet

18 Yorum

Hi, could you please tell me from where can I buy Breville BCG820BSS1BCA1 gear/limiter, the one which is in step 6. it’ll be big help.

my email is hbk.singhvi@gmail.com

sandeep singhvi - Yanıt

Hello, I need to remove the burr grinder blades. Any suggestions? There isnt a nut at the top of the grinder burr, so, not clear how to get it out.

Alexander Polson - Yanıt

Please help there is no nut how can i remove the blade?

Mohammad Khreshe -

I have the same issue with removing the lower grinder burr. The 860 doesn’t have a nut on top like other models and appears to be screwed on to the main motor shaft. Since I’m needing to replace the lower impeller I need to take it off the motor. I’ve searched high and low on the internet for any instructions, but can’t find any. I’ve tried unscrewing it, clockwise and counter-clockwise, but it just turns the motor. Really scratching my head on this one!

John Geffel - Yanıt

Sorry for late reply, I hope you found the way long time a go :-) If not, please go to Step 6.

thanhlp -

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 10

Son 7 gün: 69

Son 30 gün: 348

Her zaman: 19,457