Bu Teardown'da Kullanılan Aletler

Bu teardown bir tamir kılavuzu değildir. GD Midea FT30-3D cihazınızı onarmak için, servis kılavuzumuzu kullanın.

  1. Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.
    • Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.

    Yorum Ekle

  2. Locate the gray base support release tabs found on either side pictured in the first image.
    • Locate the gray base support release tabs found on either side pictured in the first image.

      • There are release tabs on each side of the base.

    • Press both release tabs in with the tip of your fingers and pull the gray base support until the tabs are cleared.

    Yorum Ekle

    • Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.

    • Notice that on the internal front tip of the base there is a tab. Because of this tab the back end will pivot off at that point.

    Yorum Ekle

    • After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.

    Yorum Ekle

    • Remove the following five 14.5 mm Phillips #1 screws found on the bottom.

      • All of the screws are recessed by 17.5 mm, so ensure your screwdriver can reach that far.

    Yorum Ekle

    • Once all five screws have been removed the base cover should fall right off with out any effort.

    • When putting the base cover back on; be careful to make sure that none of the wires are pinched.

    Yorum Ekle

    • Free the power switch from the base housing. Remove 2 screws.

    Yorum Ekle

  3. Free shipping on orders over $20
    Use code BLUEANDBLACK at checkout
    Free shipping on orders over $20
    Use code BLUEANDBLACK
    • Release the power cord by removing part #20 by removing 2 screws.

    Yorum Ekle

    • Remove the wire fastener(#6) by removing screw #5 to free the main wire bundle from the fan base housing.

    Yorum Ekle

    • Remove the switch. To pull the wires out of the switch gently push a screwdriver into the same hole the wire enters and the wire should slide out.

    Yorum Ekle

    • Remove the bolt that holds the fan's upper assembly from the fan body.

    Yorum Ekle

    • Remove oscillation pin by removing the screw that connects to the oscillator.

    Yorum Ekle

    • Remove front fan guard by locating and releasing 3 clips that hold it to the rear fan guard.

    Yorum Ekle

    • Remove fan blades by removing part #12. When reassembling make sure the notches in the fan blade's center line up with the perpendicular protrusions on the metal shaft.

    Yorum Ekle

    • Remove rear fan guard by removing part #13; it comes off like a screw.

    Yorum Ekle

    • Remove front fan motor housing by removing 4 screws.

    Yorum Ekle

    • Remove main fan motor housing by removing a single screw in the back.

    Yorum Ekle

    • Remove the capacitor by removing the screw that holds it to the fan.

    Yorum Ekle

    • Remove oscillation mechanism by removing the screw that connects it to the rocker arm. Push the rocker arm down and pull the oscillator off.

    Yorum Ekle

    • Remove the plug and the screw that lies beneath it.

    Yorum Ekle

Alan Su

Üyelik tarihi: 03-10-2012

531 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 24-28, Regan Fall 2012 Cal Poly, Team 24-28, Regan Fall 2012 üyesi

CPSU-REGAN-F12S24G28

4 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 2

Son 30 Gün: 10

Her zaman: 1,344