Menu

Ayarlarınız

Tezgahım

Cihazlarınız için kılavuz, parça ve cevaplara hızlı erişim edinin
Sepetim

Sepetiniz boş görünüyor

Mağazamıza Göz Atın

LaCie Minimus Teardown

Yazan: Lance Wessel (ve bir diğer katılımcı)
  • Yorumlar: 2
  • Favoriler: 0
  • Tamamlanma: 3

Zorluk

Orta

Adımlar

7

Time Required

15 - 30 dakika

Bölümler

1

İşaretler

1

Member-Contributed Guide

Üye Katkılı Kılavuz

Topluluğumuzun müthiş bir üyesi bu kılavuzu hazırladı. Bu kılavuz, iFixit personeli tarafından yönetilmiyor.

Giriş

How-To remove the internal hard drive contained within the external enclosure.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parça belirtilmedi.

  1. LaCie Minimus (2 TB hard drive)

    • LaCie Minimus (2 TB hard drive)

    Düzenle

  2. Turn the drive over, noting the black rubber strips. Carefully peel each strip off, to reveal a set of two phillips screws under each strip. Turn the drive over, noting the black rubber strips. Carefully peel each strip off, to reveal a set of two phillips screws under each strip. Turn the drive over, noting the black rubber strips. Carefully peel each strip off, to reveal a set of two phillips screws under each strip.

    • Turn the drive over, noting the black rubber strips. Carefully peel each strip off, to reveal a set of two phillips screws under each strip.

    Düzenle

  3. Remove the two sets of phillips screws and set them aside. Remove the two sets of phillips screws and set them aside.

    • Remove the two sets of phillips screws and set them aside.

    Düzenle

  4. Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın

    Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın

  5. Carefully push on the front, black faceplate to slide the drive and housing out of the case.

    • Carefully push on the front, black faceplate to slide the drive and housing out of the case.

    Düzenle

  6. Note the label: Warranty Void If Seal Broken. In this case, we want to retrieve the data and do not care about the warranty. Remove the label, to expose one of the four total screws on the side to remove the internal drive. Note the label: Warranty Void If Seal Broken. In this case, we want to retrieve the data and do not care about the warranty. Remove the label, to expose one of the four total screws on the side to remove the internal drive.

    • Note the label: Warranty Void If Seal Broken. In this case, we want to retrieve the data and do not care about the warranty. Remove the label, to expose one of the four total screws on the side to remove the internal drive.

    Düzenle

  7. Carefully remove the four screws holding the drive in the caddy, making sure that the hard drive does not slip out or damage the SATA controller card towards the rear of the case. Carefully remove the four screws holding the drive in the caddy, making sure that the hard drive does not slip out or damage the SATA controller card towards the rear of the case.

    • Carefully remove the four screws holding the drive in the caddy, making sure that the hard drive does not slip out or damage the SATA controller card towards the rear of the case.

    Düzenle

  8. The drive is now removed. Use an external hard drive reader, etc., such as the Cavalry in the second picture, to hopefully access your drive. The drive is now removed. Use an external hard drive reader, etc., such as the Cavalry in the second picture, to hopefully access your drive.

    • The drive is now removed. Use an external hard drive reader, etc., such as the Cavalry in the second picture, to hopefully access your drive.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

3 farklı kişi bu kılavuzu tamamladı.

Yazar

1 tane daha katılımcı ile

Lance Wessel

Üyelik tarihi: 31-08-2010

185 Reputation

1 Kılavuz yazıldı

Rozetler: 5

+2 tane daha rozet

2 Comments

Add a comment

Thank you !

We will need it ....

Giuseppedegioia - Yanıt

Drive inside say

5VDC / 12VDC - 0.5A 0.7A

But my replace say:

5VDC, 0,60A

12VDC, 0,45A

Is that OK or should I not change?

hlundstedt - Yanıt

Add Comment

View Statistics:

Past 24 Hours: 6

Past 7 Days: 27

Past 30 Days: 59

All Time: 4,787