Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

PlayStation 3 Super Slim Teardown - Video tutorial

Yazan: ZFix (ve 2 başka katılımcı)
  • Yorumlar: 9
  • Favoriler: 32
  • Tamamlanma: 29

Zorluk

Orta

Adımlar

10

Gerekli Süre

20 - 30 dakika

Bölümler

1

İşaretler

1

Member-Contributed Guide

Üye Katkılı Kılavuz

Topluluğumuzun müthiş bir üyesi bu kılavuzu hazırladı. Bu kılavuz, iFixit personeli tarafından yönetilmiyor.

Giriş

PlayStation 3 super slim - how to fully disassemble.

You can see also: PlayStation 3 Super Slim Teardown


Please SUBSCRIBE to my channel ツ

Videoya Genel Bakış

  1. Remove the three rubber feet, warranty sticker and four screws. Gently pull up on the bottom cover to remove it. Gently pull up on the bottom cover to remove it.

    • Remove the three rubber feet, warranty sticker and four screws.

    • Gently pull up on the bottom cover to remove it.

    Düzenle

  2. Slide the HDD cover toward the rear of the device to remove it. Remove the blue screw shown to remove the HDD caddy. Remove the blue screw shown to remove the HDD caddy.

    • Slide the HDD cover toward the rear of the device to remove it.

    • Remove the blue screw shown to remove the HDD caddy.

    Düzenle

  3. Use a metal spudger to push the tab on the rear top finisher, and lift up to remove it. Use a metal spudger to push the tab on the rear top finisher, and lift up to remove it. Use a metal spudger to push the tab on the rear top finisher, and lift up to remove it.

    • Use a metal spudger to push the tab on the rear top finisher, and lift up to remove it.

    Düzenle

  4. Repeat step 3 for the front top finisher. Repeat step 3 for the front top finisher. Repeat step 3 for the front top finisher.

    • Repeat step 3 for the front top finisher.

    Düzenle

  6. Remove the two screws indicated in the disk reader. Remove the five screws shown around the edge of the top cover. Lift the top cover up to remove it.

    • Remove the two screws indicated in the disk reader.

    • Remove the five screws shown around the edge of the top cover.

    • Lift the top cover up to remove it.

    Düzenle

  7. Move the optical disk reader assembly to the left to expose one of the screws holding the power supply in. Remove the two screws indicated and carefully disconnect the cable on the right side of the power supply. Lift the power supply up to remove it.

    • Move the optical disk reader assembly to the left to expose one of the screws holding the power supply in.

    • Remove the two screws indicated and carefully disconnect the cable on the right side of the power supply.

    • Lift the power supply up to remove it.

    Düzenle

  8. Carefully disconnect the ribbon cables indicated. Lift the optical disk reader up to remove it. Disconnect and remove the white cable and ribbon cable indicated.

    • Carefully disconnect the ribbon cables indicated.

    • Lift the optical disk reader up to remove it.

    • Disconnect and remove the white cable and ribbon cable indicated.

    Düzenle

  9. Remove the seven screws indicated. Lift the motherboard assembly up out of the lower half of the case to remove it. Carefully disconnect the Wi-Fi antenna cables and fan connector indicated by red arrows.

    • Remove the seven screws indicated.

    • Lift the motherboard assembly up out of the lower half of the case to remove it.

    • Carefully disconnect the Wi-Fi antenna cables and fan connector indicated by red arrows.

    Düzenle

  10. Remove the six screws indicated to separate the heatsink and shield from the motherboard. Remove the six screws indicated to separate the heatsink and shield from the motherboard. Remove the six screws indicated to separate the heatsink and shield from the motherboard.

    • Remove the six screws indicated to separate the heatsink and shield from the motherboard.

    Düzenle

  11. Did you do it successfully?
    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

29 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

ZFix

Üyelik tarihi: 09-12-2013

176.887 İtibar

317 adet Kılavuz yazıldı

Rozetler: 35

+32 tane daha rozet

Takım

Master Techs Master Techs üyesi

Community

295 Üyeler

968 adet Kılavuz yazıldı

7 Yorum

Yorum Ekle

What's the name of the screwdriver that undo's the star shaped screws?

themasterassassin8787 - Yanıt

It is a T8 Torx screwdriver! I'll add the tools to this guide =)

Sam Goldheart -

i took apart my ps3 super slim and put it back together but there is no power what so ever no red light at all

pastorjon.m - Yanıt

Same here did you fix it?

Kriss -

One thing to pay attention to: The T8 Torx screws (at least on my 500GB model) are Tamper Proof TR8 screws, meaning you need a special screwdriver to undo them. A normal T8 wont work.

Wesley V - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 41

Son 7 gün: 200

Son 30 gün: 971

Her zaman: 51,355