Giriş

Complete teardown of Sidekick II

Bu teardown bir tamir kılavuzu değildir. Sidekick II cihazınızı onarmak için, servis kılavuzumuzu kullanın.

  1. Use the plastic opening tool to remove the 4 buttons on each corner of the Sidekick.
    • Use the plastic opening tool to remove the 4 buttons on each corner of the Sidekick.

    • Gently pry open button and remove button.

    • Do this for each of the 3 buttons remaining.

    Yorum Ekle

  2. The bumpers on the top and bottom of the phone can be removed by simply "peeling" them off.
    • The bumpers on the top and bottom of the phone can be removed by simply "peeling" them off.

    Yorum Ekle

    • Use the Phillips head screwdriver to remove the 4 screws that are underneath the 4 buttons you removed in step one.

    Yorum Ekle

    • Flip the screen up halfway (90 degrees), to reveal the 2 screws above the right side of the keyboard.

    • Use the Torx 6 screwdriver to remove these 2 screws.

    • Be careful in handling the phone after removing the screws, because the two main bodies of the phone are no longer attached.

    Yorum Ekle

    • After removing the 6 screws and both bumpers, the phone will be easy to separate into the two main bodies.

    • You can use your hands to simply pull apart the top casing from the bottom casing.

    Yorum Ekle

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Remove screen from casing.

    Yorum Ekle

    • Remove 4 screws from back of screen using Torx 6 Screwdriver.

    • Pry screen out of casing using fingers.

    Yorum Ekle

    • Remove 4 screws from front of screen with Phillip screwdrivers.

    • Peel off the metal covering on the back of the screen.

    • Be careful when taking off the metal covering. The orange ribbon will not come out all the way, and it is fragile.

    Yorum Ekle

    • Remove the protective cover in front of the screen.

    • Do not use metal tools, you may damage the protective cover or the screen. Use your fingers only.

    Yorum Ekle

    • Take the screws out using the Torx 6 screwdriver.

    • Then lift the thumb wheel and housing off of the front panel.

    Yorum Ekle

    • Remove 2 black "rivets" from back of casing with the plastic opening tool.

    • Press keyboard out of front of casing using thumbs. Don't press too hard as you may break the board.

    Yorum Ekle

    • Remove the 5 black screws with a Phillips head screwdriver.

    • Lift the bottom of the control board from housing, and separate the two.

    Yorum Ekle

    • Carefully remove battery and back plate.

    • Do not use metal tools, you may damage the control board. Use only your fingers.

    Yorum Ekle

    • Here are all of the pieces that you have disassembled

    Yorum Ekle

michael albaum

Üyelik tarihi: 20-01-2010

45 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 3-19, Maness Winter 2010 Cal Poly, Team 3-19, Maness Winter 2010 üyesi

CPSU-MANESS-W10S3G19

4 Üyeler

11 adet Kılavuz yazıldı

Bir Yorum

nice job from a former geek

Jared Boies - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 4

Her zaman: 6,434