Ana içeriğe geç

Bu Teardown'da Kullanılan Aletler

Bu teardown bir tamir kılavuzu değildir. Texas Instruments TI-92 cihazınızı onarmak için, servis kılavuzumuzu kullanın.

  1. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Remove the protective cover. This will easily unsnap from the main body.
    • Remove the protective cover. This will easily unsnap from the main body.

  2. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Slide the tab located at the top of the calculator to the unlocked position.
    • Slide the tab located at the top of the calculator to the unlocked position.

  3. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Slide the back cover down, and then pull the back plate away from the calculator.
    • Slide the back cover down, and then pull the back plate away from the calculator.

  4. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Unscrew the back-up battery cover. (1 screw)
    • Unscrew the back-up battery cover. (1 screw)

  5. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Remove all visible screws.
    • Remove all visible screws.

    • Note that there are more screws than shown in this picture (16 in total). You MUST remove them ALL.

  6. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    Keeping the front faceplate FACE DOWN on the work surface, lift the circuit board AND the plastic backing up and away from the faceplate.
    • Keeping the front faceplate FACE DOWN on the work surface, lift the circuit board AND the plastic backing up and away from the faceplate.

  7. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    These two components are loosely attached by the rectangular module just below the back-up battery.
    • These two components are loosely attached by the rectangular module just below the back-up battery.

  8. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    The warning label next to this module reads "Do not remove the rectangular module located under the test access panel as it is required for proper product operation!"
    • The warning label next to this module reads "Do not remove the rectangular module located under the test access panel as it is required for proper product operation!"

  9. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    The rubber mat in back of the faceplate may be removed, exposing all 77 individual plastic keys.
    • The rubber mat in back of the faceplate may be removed, exposing all 77 individual plastic keys.

    • CAUTION: These keys are loosely held in by gravity and will fall out if the faceplate is tilted to any extreme.

  10. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    The device has now been separated into as many component parts as intended by the manufacturer.
    • The device has now been separated into as many component parts as intended by the manufacturer.

Daniel Maldonado

Üyelik tarihi: 14-04-2010

198 İtibar

9 adet Kılavuz yazıldı

Takım

Cal Poly, Team 15-51, Garner Spring 2010 Cal Poly, Team 15-51, Garner Spring 2010 üyesi

CPSU-GARNER-S10S15G51

5 Üyeler

9 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 2

Son 30 gün: 16

Her zaman: 8,396