Giriş

We disassembled this iPod on September 7, 2007.

Bu teardown bir tamir kılavuzu değildir. iPod Nano 3rd Generation cihazınızı onarmak için, servis kılavuzumuzu kullanın.

There it is, in the same style box as the last Nano, but quite a bit shorter and wider.
  • There it is, in the same style box as the last Nano, but quite a bit shorter and wider.

Yorum Ekle

Here's what you'll find in the box:
  • Here's what you'll find in the box:

    • A manual (even smaller than the iPod).

    • The usual, much-maligned headphones.

    • A USB to iPod cable.

    • A dock insert.

    • A brand new iPod.

Yorum Ekle

  • The growing iPod Nano family.

  • Although the new Nano is shorter and wider than its older siblings, it has approximately the same area (36 square centimeters).

Yorum Ekle

  • Apple appears to be going in circles. Anodized aluminum, shiny, anodized, shiny...

  • But of course, it's what's inside that counts.

Yorum Ekle

  • And here's our first look inside this newest Nano.

  • The case has eight locking tabs:

    • Three on the left, evenly spaced.

    • Three on top.

    • Two on the right, near the bottom, to make room for the display circuitry at the upper right.

How do i get the back panel off? it wont seem to slide up or anything

andy - Yanıt

  • We've removed six Phillips screws fixing the logic board to the casing.

  • We can now lift the logic board up, but it's still tethered by the visible click wheel cable and the hidden display cable.

Yorum Ekle

  • We've disconnected the click wheel cable and flipped the board over to disconnect the display cable.

Yorum Ekle

  • Now we use a spudger to pry up the display, which is held along the case's edge by an adhesive strip.

  • The first generation Nano's display was attached in exactly the same way. If you're not careful when prying it up, you may crack it.

Yorum Ekle

  • We're noticing a strong trend as we take apart this iPod: adhesive.

  • The click wheel is held in place by nothing but a very strong adhesive, which is going to make replacing it difficult. You'll have to get it to stay in place as well as Apple has (i.e. very well).

Yorum Ekle

  • Here the battery is out of its metal housing, which is attached to the logic board by, that's right, adhesive.

  • The battery is attached to the logic board by three through-hole solder points, as in the second generation Nano (sorry, no easy replacements).

Samsung????!!

Toni Palmer - Yanıt

Yes, that's how alot of flash based devices run Samsung chips

fraijoni - Yanıt

Of course!!!

Toni Palmer -

  • And here's everything together again, but apart.

Yorum Ekle

  • A close-up of the logic board's top, which sports an eight gigabyte Samsung flash memory chip and headphone jack.

  • The headphone jack is soldered to the logic board, as in the first generation Nano, but not in the second.

Yorum Ekle

  • A close-up of the logic board's bottom.

The top middle chip (below the dock connector is 256 megs of sdram

Lucas Hoekstra (Lucas9810) - Yanıt

Is it possible to replace the power port?

Brionced Loo - Yanıt

  • And it still works! Now, having satisfied our curiosity, we can put some music on it.

Yorum Ekle

2 Yorum

I have done the same thing to my ipod nano 3g as shown on these pics u posted.I've changed my ipod housing and now it looks as new as ever..thanks! i luv ya!

grimjaww - Yanıt

Which two out of three terminals are positive and negative.

Ravi - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 5

Son 7 Gün: 40

Son 30 Gün: 292

Her zaman: 182,933