Go on another working computer and make a Windows 10 install/recovery media by going to this link and following the instructions https://www.microsoft.com/en-us/software-download/windows10 Insert the disk into the computer and boot up. In the bios, go to the boot tab and select the usb drive under boot override. You should be booted into the windows recovery disk. Do not remove the disk. Go to repair my computer and select automatic recovery. If that does not work, then you will need to perform a fresh install.
You will likely just have to go slowly and use what is available. I would remove the mobo with this guide Dell Inspiron 15-3521 Motherboard Replacement then loosen hinge screws and slowly lift out screen. Since your screen is busted you shouldn't have to worry too much about snagging the screen cables on disassembly. Take note of how you removed the screen and now that you know how it goes out, carefully put in the new screen. If your screen isn't the full assembly you may have to loosen some hidden screws on the screen assembly pry open the top of the laptop to reveal the LCD panel to replace.
You likely have purchased a retail demo unit with a special firmware. The hardware is (probably) identical to the regular tab 4, so you can just ODIN it back to the stock consumer firmware. Instructions here, you need a PC and usb sync cable. http://forum.xda-developers.com/tab-4/general/guide-how-to-restore-stock-firmware-t2979006 Download links for FW and drivers: http://forum.xda-developers.com/tab-4/general/links-stock-galaxy-tab-4-firmware-t3013128
It can take well over 10 minutes to start off a completely dead battery. I would think iFixit batteries would come charged, but you never know. If it shows its charging(aka no lightning bolt on screen) then you should be good. Just wait like an hour and see. If still no go, then you may want to check how many amps it is drawing from usb port by splitting one of the wires apart and hooking each end to a probe on your multimeter, then measure amperage. You may also want to check voltage of battery, and or the voltage of batt. terminals on phone.
I think it should take any desktop sata drive, and you should be able to clone the old drive onto new one and extend partitions if it still works. For how to tear it down, there is no official ifixit teardown, but probably other disassembly vids.
If you can get messages but just not the notifications, you may have accidentally blocked messages/hangouts from sending notifications. Try going to settings>notifications>app notifs>messages/hangouts/whatever your messaging app is. Then reset all the settings to allow.
The contacts are loose on the male usb port end, it would require simple soldering to fix, but since chargers are so cheap, unless you have good experience soldering I'd just get a new charger to avoid ruining your phone if you repair the charger improperly.
What does your replacement display look like? does it include the plastic frame? “New motherboard” incorrectly assumes youre replacing the motherboard, if youre doing a screen, just re insert your old one.
yes and also the home button switch is different and the battery has pull tabs. its mostly the same process but omit the ones for the home button and add steps for the battery with pull tabs
one can upgrade the SSD, in this unit it is the large IC labelled TOSHIBA. I came here for the layout/orientation of the SSD/NAND chip haha
Yes they will
Really late but I agree, I refurb these earbuds a lot and came here to check which is the ground pad and which is the positive on the lil drivers
Where can you find the replacement parts?
What does your replacement display look like? does it include the plastic frame? “New motherboard” incorrectly assumes youre replacing the motherboard, if youre doing a screen, just re insert your old one.
Desoldering the emi shield is easy, even easier than ripping if you have a hot air station(doesn’t need to be a good one either)
hit up louis rossmann he might do it as a one time thing
yes and also the home button switch is different and the battery has pull tabs. its mostly the same process but omit the ones for the home button and add steps for the battery with pull tabs
12 for a copy :D the 6s screens are also dropping, it happens every year. might be different with iphone 8 oled display though
yep it is the same counterweight vibrator as the 5. I think Apple stopped using the one from the 4s because it had to be sourced from samsung.
Sayfa 1/ 3
Sonraki