Bu kullanıcı henüz profilini doldurmadı.
Cevaplar
The drip ring has to be fully on in order to stay in place. I find that the best way to do this is to turn the mixer up-side-down. Hack someone hold in place and tap all around the drip ring with a plastic mallet driving it fully in place evenly.
Devamını okuTake a look at this Service Manual which applies to the Artisan (in addition to the models listed): ++http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf++ You will, most likely, have to open up the mixer to fix the problem. Do not remove the brushes as they can be tricky to replace in the proper position.
Devamını okuTo state the obvious, something happened between disassembly and reassembly. This link takes you to the Service Manual for your mixer: ++http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf++ Things to consider: The brushes have a chamfer on one corner. This must clear a stop in the brush holder. Take a flashlight and look into the holder and make sure the brush is aligned before inserting it. Are all the wires attached to the proper tabs on the control board? Is the link that pushes on the control plate properly positioned. This link also actuates the on-off switch on the control board. The Service Manual will help you make sure that everything is in its proper place.
Devamını okuWhen everything else works except for the turntable, the usual cause is a faulty turntable motor. Replacing the motor is not that hard if you are comfortable opening ou the oven (and be sure to follow the advice about the capacitor). So far I have replaced motors on two different microwaves. My source for motors has been Ebay.
Devamını okuSee the Sevice Manual, page 8: ++http://ep.yimg.com/ty/cdn/mendingshed/ki... This applies to the 5 quart as well.
Devamını okuYou are probably not going to like thus answer. The machine has to be disassembled to push the brush out from inside. The following Service Manual will cover disassembly and checking the speed adjustment after re-assembly. Make sure that the chamfered side of the brush is in the correct position. ++http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf++
Devamını okuYour analysis is correct. The “bump” needs to better engage. This is best done by opening the machine up and 1) making sure the pivot screw holding the lever in place is not loose, and 2) if needed, remove the lever and give it a slight bend in the right direction, and reattach. Then re-adjust the mixer speed per the instructions in: ++http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf++
Devamını okuWhile the change in motor noise is most likely a motor fault, do examine the grinder itself. If the front ring is too tight, the mixer will grind (pun alert) to a halt. If the grinder is adjusted properly, the motor’s worm-follower gear is the next thing to look at. It is designed to fail and save the motor from burning out. The Service Manual can be found at: ++http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf++
Devamını okuThe wobble is not normal. Take a look at the Service Manual to see in the planetary is installed properly. Also make sure that there is no play in the shaft to which the planetary attaches. http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf
Devamını okuIf I have correctly identified the type of mixer you have, here is a link to the Service Manual: http://www.kitchenaidparts.eu/documents/...-manual/classic-svc-manual-new-email-version.pdf
Devamını okuSayfa 1 / 2
Kılavuz Yorumları
To protect the board, be sure to put heat-sink compound on the back of the new circuit (phase) board to ensure proper heat transfer to the housing.
Some corrections:
Step 1 -- Suggest (as the Service Manual does) using a flat-blade screwdriver and tap it with a light hammer to drive the drip ring off.
Step 2 -- the correct size pin punch is 5/32"
Step 3 -- Using two flat-blade screwdrivers, one on each side, pry off the planetary.
A plastic spudger is likely to break. Two points of leverage opposits each other distributes the load and prevents to the planetary and its shaft.
Step 11 -- The proper punch size is 3/32"
Steps 12 & 13 -- There is a washer on each side of the worm gear. Retain these and place one on each side off the grar when reassembling.
A link to the Service Manual:
Finkerbell
@finkerbell
127
İtibar
12
Çözümler
0
Kılavuzlar
Üyelik Başlangıç Tarihi 07/31/12