jayeff

Hi, I’m not sure but here are the installation instructions for how to stack a HE3t washer and dryer using a pedestal. You could always contact (scroll to bottom of page) this supplier and verify that your washer and dryer models are compatible with the pedestal

Hi @gmanzero Other than proving that the TV power cord is faulty or not by either disconnecting it from the outlet and the TV and testing it with an Ohmmeter or trying a compatible replacement cord, there are no other options except than to take down the TV from the wall and remove the back cover so that the power board can be inspected and tested. Here’s an image of the power board, showing the slow blow fuse (white glass fuse) and the surge suppressor (green MOV). These are the components that usually fail if there has been a power surge due to a storm or outage. If the fuse has blown replace it with an equivalent slow blow fuse (rating marked on board near fuse and also on fuse end caps e.g. T5A 250V. The T=Timed which means slow blow. If you insert a standard fuse of the same rating it will blow straight due to the high inrush currents when the power is first connected, whereas the slow blow will hold until this current has subsided. We are talking 1-2 milliseconds here for it to subside. If the fuse...

Hi @alexafujise , Check the status of the WLAN adapter in Device Manager. Open Device Manager (right click on Widows Start button, left side of Taskbar select link) and scroll down to Network Adapters, click on the > symbol to expand the list and find the WLAN adapter. Id there is a red cross next to it, right click on select enable and check if it works OK If there is a yellow exclamation mark, right click and select update drivers and follow the prompts. You need to be online (wired) to do this or manually instal them If there is no indications of any problems right click and select Properties and check the device status in the general tab. If the device is not listed, look in Device Manager > other device (if listed) and check. Update drivers if there. If noty there check Device Manager > View > show hidden devices and check If not there check in BIOS (press F2 on startup) to see if WLAN has been disabled. If still no good, here’s the service manual for the laptop, taken from this webpage. Go to p.38 to...

Hi @Shanntel Joseph, If it is not showing up in Device Manager or if there are no options to enable/disable WLAN in BIOS, the WLAN module may be loose or faulty. Here’s the hardware maintenance manual for the laptop, taken from this webpage. Go to p.66 to view the necessary pre-requisite steps and then the procedure to remove/replace the WLAN card. This will allow access to the card to check if it is connected properly and if it appears to be OK, try re-seating the card i.e. unplug and then re-insert and check if it now appears in Device Manager when the laptop is started. If still no good then perhaps the card is faulty. On p.66 you will also find the part numbers for all the cards that are compatible with the laptop. Search online using the part number only to find suppliers that suit you. The WLAN card already installed will have the part number on it or if not then at least the make and model number so this should help you to know which one may be the best to get.

Hi @Akshay Kumar Try creating a Win 10 USB recovery disc from any known working Win 10 PC. Go to Control Panel > Recovery > Create a recovery disc and follow the prompts. You will need a 8GB flashdrive and 40-60 minutes of time. When you have the recovery disc, start the laptop and get into BIOS. Change the boot order to USB 1st boot option and also enable USB Legacy setting (or CSM setting - not sure as you don't say the model) save the changes and insert the flashdrive and then restart the laptop. It should boot from the USB. When it does go to Troubleshoot > Advanced > Startup repair and follow the prompts.

Hi @joannewaite , Couldn’t find the service manual for the washer but perhaps this video may be of some help in checking if the pump itself is OK. If you need parts just search for Beko WMB71442S parts to get results for suppliers that suit you.

Hi @taile , Maybe a bit desperate but have you thought about filling the gap with conductive glue - info only?

Hi, Usually the 5V standby voltage is sent to the mainboard and it is the mainboard that turns on the Standby light when it gets this power. Also if there is this Standby power when the TV is turned on, the mainboard signals on the PS-On lead to turn the power board on full output so that it supplies all the power necessary for the backlights and the rest of the boards etc. Looking at the images you posted it appears that the power board is a BN44-00357A. Here’s the schematics for the power board. This should help to find out why there is no 5V standby voltage. Be patient when going to download the file as it takes a little while to go from processing to download once you have passed the recaptcha test and clicked on Go to Download under the document preview box. Hopefully a start.

Hi @iotriton What is the model number of the refrigerator? Can you hear if the evaporator fan is running? The evaporator fan will run as long as the compressor is running and both the doors are shut.It will stop when a door (either door) is opened Without knowing the model number the following may not work but if the refrigerator/freezer have visible door switches located in the door jamb, when the compressor is running open the freezer door and then manually operate the door switch. If there are lights in the freezer compartment they should turn off but more importantly the evaporator fan which is located with the evaporator unit behind a panel inside the freezer compartment at the back will start running again. Check if you can hear it stop and start or feel the air from the vent when the switch is released and operated. If there are no visible door switches (they could be concealed magnetic reed switches - depends on model), then listen closely and check if you can hear the fan stop and start when you...

Hi, If your washer is a Samsung B1445A then here’s the start of the troubleshooting section of the service manual. Go to Item # 4 to view the possible causes of the problem. The following pages have circuit details etc which may help. Here’s how to get to the Driving Compartment test mode which may also give some clues as to what is happening. Hopefully a start.

The 3rd wire from a battery is usually connected to a thermistor attached to the battery which signals the temperature (resistance value changes with temp) to the battery management circuit in the motherboard.

Charging will be halted to if it got too hot before being fully charged, which may create problems e.g. a fire

If leaving the 3rd wire disconnected, the battery should not be left unsupervised whilst it is charging

The 3rd wire is usually connected to a thermistor attached to the battery which gives the battery management circuitry in the motherboard an indication of the temperature of the battery when it is being charged. The temperature (actually a resistance measurement that alters with the temperature) is used in conjunction with the voltage level, so that the battery is not being overcharged and getting too hot and creating potential problems if left charging unattended for long periods. The charging process is halted

Hi @captainsnowball ,

FYI

voilà French exclamation - meaning “There it is!” or “There you are!”

The “red thing” in Step 3 is most probably an IR filter, to filter out visible light to improve IR operation

Hi, As yet I haven't figured out how to amend the link to the User Guide for this radio. The one in the Repair Guide no longer exists, so here is one that still works

https://midlandusa.com/wp-content/upload...