I am getting error code (8002F147) on my PS3

Question

PlayStation 3

PlayStation 3 (veya daha sık bilinen adıyla PS3), Sony Computer Entertainment tarafından üretilen üçüncü ev bilgisayar eğlence sistemidir ve PlayStation 2'nin akabinde devamı olarak üretilmiştir. 11 Kasım 2006'da piyasaya sürüldü.

20 Soru Tümünü görüntüle | 28 Parçalar Mağaza

impactsk8er100 @impactsk8er100

İtibar: 313

2

1

Gönderildi: 29 Eki 2010

Seçenekler

I am getting error code (8002F147) on my PS3

Alright so I have 2 PS3s. My friend let me borrow his broken ps3 to try to fix it. The problem is that he unplugged the AC unit during the update. So now I have error code (8002F147). Everytime I tried to restart it, it still went to update. It goes to about 36% then it gives me the error. It's an endless loop of errors.

IS THERE ANY WAY TO FIX THIS BESIDES SENDING IT TO SONY???

Yanıtlandı! Cevabı görüntüle Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Evet Hayır

Puan 26

3 Yorum

My nephew just brought me his PS3 today with the same exact problem. I will try messing around with it and I will let you know what happens.

Xnriq tarafından 29 Eki 2010

Plz let me no the problem too

gregwebb83 tarafından 28 Kas 2019

السلام عليكم اردنا ان نقم بتحديث البلاستيشن ٣ و عندما انتهى التحديث ضهرت رسالة تقول بأنه تم حذف التحديث السابق و يتم التحديث الان من جديد وبعد ان ينتهي من التحديث يكتب فشل و اذا اردت اتصل على 8002f147

كيف اعمل انها عملية متكررة عندما تشتغل يبدأ التحديث مباشرتا ونحن في الوسط اي انه لم يتم التحديث ولم نستطع الخروج من التحديث

خالد الهطالي tarafından 10 Nis 2020

Yorum Ekle

11 Cevap

Seçilen Çözüm

bushing @bushing

İtibar: 10,3b

45

20

47

Gönderildi: 29 Eki 2010

Seçenekler

I found this answer on a forum (link below):

take out the hard drive
connect hard drive to pc
open up disk management - in win7 it asked me to make a master book record, so I did.
format in NTFS - that's right, NTFS - don't use quick format
get the rom of whatever version you were on before you upgraded - i had to search, but i found the us 3.30 rom
copy that rom to usb drive in folders PS3 ==> UPDATE ==> put rom named PS3UPDAT.PUP here
shut down pc, take out hd, take usb drive too
put hd back in ps3, put usb stick in ps3
boot ps3
a screen will pop up. press select + start
another screen (i think) later, press select + start
configure your ps3 setup - done

(source: http://forums.demigodthegame.com/386771)

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 9

5 Yorum:

Yes I seen that. I dont have a SATA cable though so I just tried to update via full format on other PS3. It might work.

impactsk8er100 tarafından 29 Eki 2010

Every time I try to update my ps3 to 3.55 firmware it give these error code80028cca

jarell tarafından 25 Tem 2016

Super slim ?

HULK 23cze tarafından 10 Mar 2019

There is no hard drive on my ps3, what to do

VIKRANT RAJ tarafından 10 Eki 2019

The problem persists in the drive strip make sure its plugged in good and tite on both ends from drive to board i had to add a small thick piece of paper to the stripp to make sure it was snug and make sure the little black lever is up b4 u insert and pressed down when snug i just did this and it installed first try

Jake Oneal tarafından 16 Eki 2019

Yorum Ekle

My nephew just brought me his PS3 today with the same exact problem. I will try messing around with it and I will let you know what happens. — Xnriq
السلام عليكم اردنا ان نقم بتحديث البلاستيشن ٣ و عندما انتهى التحديث ضهرت رسالة تقول بأنه تم حذف التحديث السابق و يتم التحديث الان من جديد وبعد ان ينتهي من التحديث يكتب فشل و اذا اردت اتصل على 8002f147

كيف اعمل انها عملية متكررة عندما تشتغل يبدأ التحديث مباشرتا ونحن في الوسط اي انه لم يتم التحديث ولم نستطع الخروج من التحديث — خالد الهطالي
Yes I seen that. I dont have a SATA cable though so I just tried to update via full format on other PS3. It might work. — impactsk8er100
Every time I try to update my ps3 to 3.55 firmware it give these error code80028cca — jarell
The problem persists in the drive strip make sure its plugged in good and tite on both ends from drive to board i had to add a small thick piece of paper to the stripp to make sure it was snug and make sure the little black lever is up b4 u insert and pressed down when snug i just did this and it installed first try — Jake Oneal

Xnriq @macrepairphx İtibar: 2,7b 21 8 6 · Answer 1 · 2010-11-10T00:48:40-07:00

Xnriq @macrepairphx

İtibar: 2,7b

21

8

6

Gönderildi: 10 Kas 2010

Seçenekler

Hey man as I mentioned before my nephews PS3 had the same problem. All I did to fix it was:

tear the entire PS3 apart to clean it and re apply thermal paste.
While I had the mobo out I thought about removing the PRAM battery to see if that would fix the update error.
After I put the PS3 back together I turned it on WITHOUT a hard drive then when the missing HD error came up I inserted the HD then turned the PS3 off.
I turned it back on and the update ran right off the batt as usual except it was updating much faster. I just let it finish and it actually finished the update and booted into the home screen.

All his saved data as well as media was still there and it is now running fine. I do not think you have to do the whole thermal paste deal but just remove the PRAM battery for a while then try what I did with the HD. I hope this helps. Good luck!!

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 3

3 Yorum:

I can confirm that this solution will fix the problem. Granted, the PS3 I was working on was giving the 802F1F9 error, but it is worth a shot. I did not do any thermal paste re-application, just removed the small onboard battery for a minute or two, reassembled, and start it first without then with the harddrive. Nice fix. +

Brett Hartt tarafından 9 Mar 2011

can not be formatted if the windows 10

Hafizdanish tarafından 9 Kas 2016

nope still getting the error...

gogogamezzz z tarafından 10 Mar 2018

Yorum Ekle

Ruben Molina @rubenmolina İtibar: 25 1 · Answer 2 · 2013-07-01T20:31:34-07:00

Ruben Molina @rubenmolina

İtibar: 25

1

Gönderildi: 1 Tem 2013

Seçenekler

Does anyone know where I can get the 3.30 or 3.40 firmware? I'm currently stuck with the same issue. {PS# SLIM 160GB}.

Thanks in advance!

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 2

Yorum Ekle

mmk @mmk İtibar: 13 1 · Answer 3 · 2016-02-04T17:46:23-07:00

mmk @mmk

İtibar: 13

1

Gönderildi: 4 Şub 2016

Seçenekler

I need repair this error plz

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 1

Yorum Ekle

chox @chox52425 İtibar: 1 · Answer 4 · 2011-03-09T11:59:46-07:00

chox @chox52425

İtibar: 1

Gönderildi: 9 Mar 2011

Seçenekler

error code 8002f147 refers to a problem with your disc drive/blue-ray player, if you have recently had it repaired from ylod or other problems that's probably whats done it, there are little plastic clips connecting the lead from the main board to your drive and i bet you find its broke or if its not been fixed lately i think you may need a new drive!!!

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 0

1 Yorum:

You can't replace the blu-ray drive on a PS3 the motherboard to the drive is married to the motherboard of the console. They are a set that can't be separated and work. Please do a Google on the PS3 error code 8002f147, it is a firmware error.

ABCellars tarafından 9 Mar 2011

Yorum Ekle

Hafizdanish @danish48 İtibar: 1 · Answer 5 · 2016-11-09T22:09:48-07:00

Hafizdanish @danish48

İtibar: 1

Gönderildi: 9 Kas 2016

Seçenekler

can not be formatted if

the windows 10

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 0

Yorum Ekle

Pjabeyta @pjabeyta1348 İtibar: 1 · Answer 6 · 2017-01-14T22:59:50-07:00

Pjabeyta @pjabeyta1348

İtibar: 1

Gönderildi: 14 Oca 2017

Seçenekler

Nothing has helped. Same error. PS3 slim. I used three new drives. All kinds of formatting. Downloaded newest firmware. It recognizes the drive with firmware and even displayed it on the screen. Still no go. Any ideas?

Thanks.

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 0

Yorum Ekle