JBL FLIP 3

Question

Repair and support for the third generation of the Flip portable speaker by JBL.

70 Soru Tümünü görüntüle

XxMasked ManxX @xxmaskedmanxx

İtibar: 23

2

1

Gönderildi: 22 Eki 2017

Seçenekler

JBL FLIP 3 - Piece of motherboard fell off labelled 1R5

I dropped by speaker a little while ago, it approximately fell from 1.4 meters, as soon as it dropped the audio stopped, I checked it, the battery charges, it connects to Bluetooth and the led display works, so I further investigated because I could here a rattle, I have check the motherboard and found a piece that looks like it has been de attached from the motherboard labelled 1R5? Is this fixable?

Yanıtlandı! Cevabı görüntüle Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Evet Hayır

Puan 1

6 Yorum

Help required please

XxMasked ManxX tarafından 23 Eki 2017

where is it placed on the mother board?

LunarYTS tarafından 6 Mar 2018

Hi, I have the same problem but when I put the inductor in its place and turn on the speaker it really heats up and even releases smoke. Any help with that?

Fernando Ramonborja tarafından 29 Haz 2019

Hey guys I wanted to ask how do I attach this price onto the motherboard I have the same problem the “1R5” piece

champs49ers tarafından 6 Oca 2020

Where can I get a replacement part for the broken 1R5 part?

Daniel Sepulveda tarafından 2 Ağu 2020

1 tane daha yorum göster

Yorum Ekle

1 Cevap

Seçilen Çözüm

daniel @tech_ni

İtibar: 34,6b

10

22

44

Gönderildi: 23 Eki 2017

Seçenekler

yes its fixable its a coil, you need to find the place it came of on the board and solder it on, but you would need to see if the pads have been damaged

Bu yanıt yardımcı oldu mu?

Evet Hayır

Puan 5

4 Yorum:

Thanks for your help, I had got impatient so I decided to play around and found where it went and the sound worked so I soldered it back on and there we go done.

XxMasked ManxX tarafından 23 Eki 2017

Hello my name is David I have the same problem you describe ! I would like to ask for an explanation about how to solder it back , i don't know how to do it or to verify if the pads are damaged

Please help me

Thank you and advance

David Mencias tarafından 31 Oca 2018

Check to make sure the pads are shiny metal. If they are dull green material, the pads are damaged. If they are metal, they are good.

Due to how JBL assembles this speaker, dont bother taking the board out. Just remove the front speakers (carefully using a screwdriver to disconnect the connector) and the side diaphrams. Tin the pads and the 1R5 part (called an inductor), then remove the excess solder with a wick. Use a chisel tip soldering iron to solder one side at a time, being careful not to melt the case. Hold it for like 15-30 seconds on each joint so you get a good connection: the reason it failed in the first place was that JBL had cold solder joints.

Ella Jameson tarafından 15 May 2018

does anyone know how to test the coil or even replace it. I checked ebay cant find any .

migel anguiano tarafından 31 Ağu 2018

Yorum Ekle

Hi, I have the same problem but when I put the inductor in its place and turn on the speaker it really heats up and even releases smoke. Any help with that? — Fernando Ramonborja
Hey guys I wanted to ask how do I attach this price onto the motherboard I have the same problem the “1R5” piece — champs49ers
Thanks for your help, I had got impatient so I decided to play around and found where it went and the sound worked so I soldered it back on and there we go done. — XxMasked ManxX
Hello my name is David I have the same problem you describe ! I would like to ask for an explanation about how to solder it back , i don't know how to do it or to verify if the pads are damaged

Please help me

Thank you and advance — David Mencias
Check to make sure the pads are shiny metal. If they are dull green material, the pads are damaged. If they are metal, they are good.

Due to how JBL assembles this speaker, dont bother taking the board out. Just remove the front speakers (carefully using a screwdriver to disconnect the connector) and the side diaphrams. Tin the pads and the 1R5 part (called an inductor), then remove the excess solder with a wick. Use a chisel tip soldering iron to solder one side at a time, being careful not to melt the case. Hold it for like 15-30 seconds on each joint so you get a good connection: the reason it failed in the first place was that JBL had cold solder joints. — Ella Jameson
does anyone know how to test the coil or even replace it. I checked ebay cant find any . — migel anguiano

JBL Flip 3

JBL FLIP 3 - Piece of motherboard fell off labelled 1R5

1 Cevap

Yanıtını ekle