Ana içeriğe geç

Flagship smartphone from Huawei released April 2019. Featuring a 6.47" FHD+ OLED screen, in-display fingerprint sensor, 40 MP main camera plus 8 MP telephoto camera and a new earpiece speaker technology. Model VOG-L29 and VOG-L09.

49 Soru Tümünü görüntüle

What resistors are these? (zxw)

I accidentally broke three resistors on the main motherboard of the device. And I want to solder the resistors independently.

I would be happy if someone who has the software zxw can find me the resistance level and the size of these resistors.

(By the way, so that more people can use this in the future, I will mention that two of them are on the sim way)

Block Image

Block Image

I marked the resistors here.

Thanks!

huawei p30 pro

Bu soruyu yanıtla Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Puan 2
6 Yorum

@haim1, What is the board number on your phone? I’ll see if I can dig up a schematic and boardview.

tarafından

@geirandersen to be sure.

tarafından

@geirandersen L 29 if you talk about that

tarafından

1 tane daha yorum göster

Yorum Ekle

1 Cevap

Filtre ölçütü:
En Yararlı Yanıt

Had a look at XZZ, since I tend to not use ZXW where schematics are concerned. Resistors in question are as follows:

R3003 (green) 47 ohms

R3001 (yellow) 100 ohms

R3006 (orange) 1K ohms

Block Image

Hope that helps!

Adding 01/31/2023 - for Андрей Лукьянов

According to the files I have

Block Image



C2901 (red) schematic says 100n? Which i would interpret as nanofarads? That's sort of an atypical way to write that, I would have just said .1µF but that's beside the point.

R2902 (blue) 2K ohms

C2906 (purple) 33pF

Bu yanıt yardımcı oldu mu?

Puan 5

9 Yorum:

Thanks you.

Just to be sure.... can you write me the size of the resistors?

And one more question... I search on googleans some websites "R3003" for example and i dont find this power of resist (47ohm). Why?

tarafından

@haim1 R3003 is the components designation on this exact board, it’s value is 47 ohms. As for size (package), it’s most likely 0402

tarafından

Thanks!!!!!!

tarafından

@haim1 @geirandersen is correct about the designations. That's just how Huawei refers to the resistor in that location on that specific board. So they don't have to say the resistor fourth in from the left, or something like that.

As for size, the schematic doesn't specify. 0402 is quite large for a resistor, but they do look bigger than resistors on most iPhone boards, which is what I am most accustomed to (those are almost always 1005). So I would wager you're right. Either than or 0201.

tarafından

@flannelist I almost wrote 1005 without even considering anything else, but I took a last look at the picture in the question and I realised the pads looked fairly huge. Now, they could very well be 0201, my eyes ain’t that good looking at a picture on then screen :P

tarafından

4 tane daha yorum göster

Yorum Ekle

Yanıtını ekle

Haim Falah sonsuza kadar minnettar olacak.
İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 17

Son 30 gün: 38

Her zaman: 641