Eşyalarını Tamir Et Topluluk Mağaza

4Sight 9 Screen Replacement

Giriş

If your 4Sight 9’s screen has been cracked, is not responding to touch, or has a dead backlight, use this guide to replace it.

Neye ihtiyacın var

  1. 4Sight 9 Screen Replacement, Cover: adım 1, 2 resimden 1. 4Sight 9 Screen Replacement, Cover: adım 1, 2 resimden 2.

    • Place the tablet on its side so that the two screws are facing upward.

    • Remove two 1 mm screws from the left side of the tablet using a Phillips #00 screwdriver.

    Düzenle

  2. 4Sight 9 Screen Replacement: adım 2, 1 resimden 1.

    • Pry the case away from the device slowly by sliding a plastic opening tool along the device.

    • Once loosened, use your hands to separate the case from the device.

    Düzenle

  3. 4Sight 9 Screen Replacement: adım 3, 2 resimden 1. 4Sight 9 Screen Replacement: adım 3, 2 resimden 2.

    • Hold the positive and negative wires as close as possible to the speaker.

    • Use an opening tool and fingers to simultaneously lift the speaker from the cover.

    Düzenle

  4. 4Sight 9 Screen Replacement, Battery: adım 4, 1 resimden 1.

    • Use soldering gun to remove the positive and negative wires connecting the battery to the circuit board.

    • For a complete guide on how to solder, click here.

    Düzenle

  5. 4Sight 9 Screen Replacement: adım 5, 2 resimden 1. 4Sight 9 Screen Replacement: adım 5, 2 resimden 2.

    • Insert plastic prying tool under upper-hand corner of battery and slide back and forth.

    • Once loosened, insert plastic prying tool under lower-hand corner and repeat sliding action.

    • Repeat previous actions until battery comes loose from device.

    Düzenle

  7. 4Sight 9 Screen Replacement, Screen: adım 6, 2 resimden 1. 4Sight 9 Screen Replacement, Screen: adım 6, 2 resimden 2.

    • Grip the ribbon located at the far end of the circuit board with a plastic spudger tool.

    • Put pressure on the connector until the clasp comes undone.

    • Gently pull up on electrical ribbon until it disconnects from circuit board.

    Düzenle

  8. 4Sight 9 Screen Replacement: adım 7, 2 resimden 1. 4Sight 9 Screen Replacement: adım 7, 2 resimden 2.

    • Remove the second electrical ribbon from the motherboard using the same technique used to remove first ribbon.

    Düzenle

  9. 4Sight 9 Screen Replacement: adım 8, 1 resimden 1.

    • Using #00 Phillips Screwdriver, remove the four 1mm screws holding the circuit board to the device.

    Düzenle

  10. 4Sight 9 Screen Replacement: adım 9, 2 resimden 1. 4Sight 9 Screen Replacement: adım 9, 2 resimden 2.

    • With fingers, grip the green Wi-Fi connector.

    • Gently pull up on connector to remove tape holding the connector in place.

    Düzenle

  11. 4Sight 9 Screen Replacement: adım 10, 2 resimden 1. 4Sight 9 Screen Replacement: adım 10, 2 resimden 2.

    • With the motherboard facing you, look to the bottom left corner, pull on the camera to completely free the motherboard.

    Düzenle

  12. 4Sight 9 Screen Replacement: adım 11, 1 resimden 1.

    • Using your fingers, gently lift the motherboard and battery.

    Düzenle

  13. 4Sight 9 Screen Replacement: adım 12, 3 resimden 1. 4Sight 9 Screen Replacement: adım 12, 3 resimden 2. 4Sight 9 Screen Replacement: adım 12, 3 resimden 3.

    • Insert plastic prying tool under screen and exert pressure, pulling upward.

    • Repeat this step around each corner of the screen until it pops off.

    • Ensure screen is free from all black tabs holding it in place.

    Düzenle

  14. 4Sight 9 Screen Replacement: adım 13, 1 resimden 1.

    • Place heating pad on glass frame in order to loosen adhesive for 3 to 5 minutes

    • Remove plastic film from glass frame

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 gün: 4

Son 30 gün: 13

Her zaman: 2,898