Eşyalarını Tamir Et Topluluk Mağaza

ATT CL2940 Speakerphone Replacement

Yazan: Charles Messmore (ve 7 başka katılımcı)
  • Yorumlar: 1
  • Favoriler: 1
  • Tamamlanma: 1

Zorluk

Orta

Adımlar

6

Gerekli Süre

30 - 40 dakika

Bölümler

2

İşaretler

1

Better Introduction

Daha iyi giriş

Girişi tamamlayarak ya da daha iyi hale getirerek bu kılavuzu geliştirin.

Giriş

A speakerphone is used to talk hands-free on the phone. This guide will educate you on how to replace one if it is part of your ATT CL2940.

You will need to solder to complete this guide. If you are not familiar, check out this article for an introduction.

  1. Remove five 9.5 mm Phillips #1 screws from the back panel of the phone. Remove five 9.5 mm Phillips #1 screws from the back panel of the phone. Remove five 9.5 mm Phillips #1 screws from the back panel of the phone.

    • Remove five 9.5 mm Phillips #1 screws from the back panel of the phone.

    Düzenle

  2. Slide the metal spudger into the crack and continue around to the front panel of the phone. Be careful not to break the clips that hold the back panel to the front panel. Be careful not to break the clips that hold the back panel to the front panel.

    • Slide the metal spudger into the crack and continue around to the front panel of the phone.

    • Be careful not to break the clips that hold the back panel to the front panel.

    Düzenle

  4. When setting the back panel down, be careful to not rip any of the wires off of the internal components.

    • When setting the back panel down, be careful to not rip any of the wires off of the internal components.

    Düzenle

  5. Remove the front panel of the device as shown. Remove the front panel of the device as shown.

    • Remove the front panel of the device as shown.

    Düzenle

  6. Desolder the speakerphone with a soldering iron. If you are unfamiliar with solder, check out the article on soldering and be very careful. The iron is hot! If you are unfamiliar with solder, check out the article on soldering and be very careful. The iron is hot!

    • Desolder the speakerphone with a soldering iron.

    • If you are unfamiliar with solder, check out the article on soldering and be very careful. The iron is hot!

    Düzenle

  7. Use the soldering iron to reconnect the wires to the new speaker. Place the new speaker back in place.

    • Use the soldering iron to reconnect the wires to the new speaker.

    • Place the new speaker back in place.

    • Make sure that all of the components are back in place.

    Düzenle
Bitiş Çizgisi

Bir başkası bu kılavuzu tamamladı.

Yazar

7 tane daha katılımcı ile

Charles Messmore

Üyelik tarihi: 15-02-2016

541 İtibar

5 adet Kılavuz yazıldı

Rozetler: 12

+9 tane daha rozet

Takım

IUPUI, Team 1-1, Harley Spring 2016 IUPUI, Team 1-1, Harley Spring 2016 üyesi

IUPUI-HARLEY-S16S1G1

4 Üyeler

13 adet Kılavuz yazıldı

Bir Yorum

Why do all these repairs require NO PARTS to replace defective parts?

And, of course< there is no links to a place to purchase the needed parts...

rpoland - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 2

Her zaman: 476