Eşyalarını Tamir Et Topluluk Mağaza

Black and Decker LDX 120C Light Replacement

Giriş

If the light in the drill is not glowing upon use, then this guide will show a step by step process on how to replace the light bulb for the drill.

Neye ihtiyacın var

  1. Black and Decker LDX 120C Light Replacement, Outer Case: adım 1, 1 resimden 1.

    • For this guide we will need to use a 1.0 mm phillips #1 screw.

    • There are a total of thirteen screws that need to be removed in order to open the drill and access the interior components.

    Düzenle

  2. Black and Decker LDX 120C Light Replacement: adım 2, 1 resimden 1.

    • Remove the four screws on the back top side of the drill.

    Düzenle

  3. Black and Decker LDX 120C Light Replacement: adım 3, 1 resimden 1.

    • Remove the four screws that connect the chuck to the drill.

    Düzenle

  4. Black and Decker LDX 120C Light Replacement: adım 4, 1 resimden 1.

    • Remove the five screws on the front side of the drill.

    Düzenle

  5. Black and Decker LDX 120C Light Replacement: adım 5, 1 resimden 1.

    • Gently grab both sides of the drill casing, and separate both sides from each other.

    Düzenle

  7. Black and Decker LDX 120C Light Replacement: adım 6, 1 resimden 1.

    • At this point you should be able to separate both as illustrated.

    Düzenle

  8. Black and Decker LDX 120C Light Replacement: adım 7, 1 resimden 1.

    • Now all the components of the drill are visible and can be accessed.

    Düzenle

  9. Black and Decker LDX 120C Light Replacement, Light: adım 8, 1 resimden 1.

    • After following the prerequisite guide the drill is now open and you can see all the components of the drill.

    Düzenle

  10. Black and Decker LDX 120C Light Replacement: adım 9, 1 resimden 1.

    • First separate the top part of the drill, which includes the motor and the chuck, from the rest of the components.

    • Remove carefully so that wire connection is not damaged throughout this process.

    Düzenle

  11. Black and Decker LDX 120C Light Replacement: adım 10, 1 resimden 1.

    • Then separate the other component which includes the trigger, light, and the connection to the battery.

    • Do this carefully so that no wire connection or any component gets damaged.

    Düzenle

  12. Black and Decker LDX 120C Light Replacement: adım 11, 1 resimden 1.

    • First check if the connection to the light is not intact.

    • If the wiring is lose simply reconnect the wire.

    • Then check if the light bulb is not damaged in any way.

    • If the light bulb is broken or simply just burnt; simply replace the light bulb.

    Düzenle

  13. Black and Decker LDX 120C Light Replacement: adım 12, 1 resimden 1.

    • Grab the connection of the light bulb.

    Düzenle

  14. Black and Decker LDX 120C Light Replacement: adım 13, 1 resimden 1.

    • Using pliers cut the two connecting wires from the mother chip.

    • To prevent potential damage to the component, try desoldering the wires. Learn more about soldering here.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

jeffrey zakka

Üyelik tarihi: 02/09/16

762 İtibar

6 adet Kılavuz yazıldı

Rozetler: 14

+11 tane daha rozet

Ekip

USF Tampa, Team 11-5, Cheng Spring 2016 USF Tampa, Team 11-5, Cheng Spring 2016 üyesi

USFT-CHENG-S16S11G5

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 gün: 5

Son 30 gün: 43

Her zaman: 17,815