Giriş

Replace or upgrade your Phantom motors. This guide requires soldering.

Each motor's direction is determined by the order of its leads on the ESC, so when you're replacing, be sure to match the original order. Motors on opposite arms will have the same direction, so check the other arm for reference.

If you're ordering a replacement, be sure to get the right thread direction for your motor, or the propellor collet will loosen during flight.

Parçalar

Press down on battery door release tab to flip the battery door open. Press down on battery door release tab to flip the battery door open. Press down on battery door release tab to flip the battery door open.
  • Press down on battery door release tab to flip the battery door open.

Yorum Ekle

Pull out the battery pack. Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints. Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints.
  • Pull out the battery pack.

  • Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints.

Yorum Ekle

Pull the two halves of the XT60 power connector apart. It's a tight fit, so be careful not to hit your drone or yank on the cables when it releases!
  • Pull the two halves of the XT60 power connector apart.

    • It's a tight fit, so be careful not to hit your drone or yank on the cables when it releases!

Yorum Ekle

Silver-topped propeller collets unscrew counter-clockwise Black-topped propeller collets unscrew clockwise
  • Silver-topped propeller collets unscrew counter-clockwise

  • Black-topped propeller collets unscrew clockwise

Yorum Ekle

For propellors with silver collets: Use a 12 mm wrench or socket to loosen silver collets in the counter-clockwise direction. Once free, unscrew and remove the collet. Once free, unscrew and remove the collet.
  • For propellors with silver collets: Use a 12 mm wrench or socket to loosen silver collets in the counter-clockwise direction.

  • Once free, unscrew and remove the collet.

Yorum Ekle

For propellors with black collets: Use a 12 mm wrench or socket to loosen black collets in the clockwise direction. Once free, unscrew and remove the collet. Once free, unscrew and remove the collet.
  • For propellors with black collets: Use a 12 mm wrench or socket to loosen black collets in the clockwise direction.

  • Once free, unscrew and remove the collet.

Yorum Ekle

Gently press down the motor shaft and lift the propeller up to remove it. Gently press down the motor shaft and lift the propeller up to remove it. Gently press down the motor shaft and lift the propeller up to remove it.
  • Gently press down the motor shaft and lift the propeller up to remove it.

Yorum Ekle

After removing all four propellors, flip the drone over. Remove the following screws from the underside of the drone: Twelve 2.0 mm hex screws
  • After removing all four propellors, flip the drone over.

  • Remove the following screws from the underside of the drone:

    • Twelve 2.0 mm hex screws

    • Four Phillips #0 screws

Yorum Ekle

Loosen the cable from the plastic landing gear. Unplug the magnetometer molex connector. Unplug the magnetometer molex connector.
  • Loosen the cable from the plastic landing gear.

  • Unplug the magnetometer molex connector.

Yorum Ekle

Lift up on the top portion of the shell and set it on its side. Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables. Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables.
  • Lift up on the top portion of the shell and set it on its side.

  • Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables.

Yorum Ekle

Lift the GPS cable molex connector up out of its socket on the main board. Lift the GPS cable molex connector up out of its socket on the main board.
  • Lift the GPS cable molex connector up out of its socket on the main board.

On the Phantom FCP40 (essentially a Phantom 1), the GPS cable connects directly to the Naza controller box, not to the board as shown here. Also the compass (magnetometer) is connected to the main board, not the GPS unit in the top shell, so you don't need to remove it to remove the top shell.

Marcus Bointon - Yanıt

Gently pull the slack of the magnetometer cable through the case bottom shell. The case top shell should now have enough slack to work on the interior of the Phantom. The case top shell should now have enough slack to work on the interior of the Phantom.
  • Gently pull the slack of the magnetometer cable through the case bottom shell.

  • The case top shell should now have enough slack to work on the interior of the Phantom.

Yorum Ekle

Desolder all three motors wires from the speed controller board. Follow our soldering guide to learn how, or just to brush-up on your skills.
  • Desolder all three motors wires from the speed controller board.

    • Follow our soldering guide to learn how, or just to brush-up on your skills.

  • Be careful not to melt the plastic case bottom shell with your soldering iron or damage any electronic components.

  • When you're reassembling, solder the motor leads back in their original order. This may be different from the picture. Motors on arms across from each other have the same color order, so check the opposite arm for reference.

Yorum Ekle

Unscrew the four 2 mm motor hex bolts from the case bottom shell.
  • Unscrew the four 2 mm motor hex bolts from the case bottom shell.

Yorum Ekle

Remove the motor from the Phantom. Remove the motor from the Phantom.
  • Remove the motor from the Phantom.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 başka kişi bu kılavuzu tamamladı.

David Hoyt

Üyelik tarihi: 09-04-2010

3.596 İtibar

44 adet Kılavuz yazıldı

Takım

Cal Poly, Team 25-89, Amido Spring 2010 Cal Poly, Team 25-89, Amido Spring 2010 üyesi

CPSU-AMIDO-S10S25G89

4 Üyeler

52 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 4

Son 7 Gün: 35

Son 30 Gün: 151

Tüm Zamanlar: 15,591