Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Motorola Moto G7 Play Camera Replacement

Yazan: Monserath Casillas (ve 4 başka katılımcı)
  • Yorumlar: 1
  • Favoriler: 0

Zorluk

Kolay

Adımlar

6

Gerekli Süre

25 dakika

Bölümler

2

İşaretler

0

Giriş

This guide will show users how to replace a defective or damaged rear camera lens in the Motorola Moto G7 Play. This guide applies to both the XT1952-3 and XT1952-2 models. The rear camera lens is capable of taking 13MP photos as well as 1080p video. Users may need to replace the camera if the lens is badly damaged. A damaged lens affects photo quality in the camera.

  1. Turn off your device before you begin. Use the iFixit pick to break the adhesive around the back case.

    • Turn off your device before you begin.

    • Use the iFixit pick to break the adhesive around the back case.

    • Use a heat gun, hairdryer, or iOpener to weaken the adhesive around the back case. If you're using the iOpener, please review the instructions for proper use.

    Düzenle

  2. Detach the back case from the phone.

    • Detach the back case from the phone.

    • Make sure the back is opened right to left so the cable of the fingerprint scanner does not get damaged.

    Düzenle

  3. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

  4. Use the iFixit pick and the iFixit opening tool to pull the fingerprint scanner off of the back case. Use the iFixit pick and the iFixit opening tool to pull the fingerprint scanner off of the back case.

    • Use the iFixit pick and the iFixit opening tool to pull the fingerprint scanner off of the back case.

    Düzenle

  5. Remove the nine 3.2mm screws from the motherboard cover with a Phillips #00 screwdriver.

    • Remove the nine 3.2mm screws from the motherboard cover with a Phillips #00 screwdriver.

    Düzenle

  6. Lift the motherboard cover from the bottom.

    • Lift the motherboard cover from the bottom.

    • Use reverse tweezers or a similar tool if needed.

    Düzenle

  7. Once the motherboard cover is removed, use the iFixit opening tool to disconnect the ribbon cable connecting the camera to the motherboard. The camera can now be removed and is ready to be replaced.

    • Once the motherboard cover is removed, use the iFixit opening tool to disconnect the ribbon cable connecting the camera to the motherboard.

    • The camera can now be removed and is ready to be replaced.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Monserath Casillas

Üyelik tarihi: 10-02-2020

901 İtibar

5 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Takım

Cal Poly, Team S7-G4, Regan Winter 2020 Cal Poly, Team S7-G4, Regan Winter 2020 üyesi

CPSU-REGAN-W20S7G4

5 Üyeler

10 adet Kılavuz yazıldı

Bir Yorum

Yorum Ekle

My camera stopped working after water damage. Replacing the camera itself didn’t fix it. What could the problem be?

abb - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 2

Son 30 gün: 21

Her zaman: 329