Flip over the turntable and remove the 9 screws on the outer edges. Flip over the turntable and remove the 9 screws on the outer edges.
  • Flip over the turntable and remove the 9 screws on the outer edges.

Yorum Ekle

Remove the back cover by pulling it apart.
  • Remove the back cover by pulling it apart.

Yorum Ekle

Remove the clip located on the backside of the audio jack housing by gently pulling it out. There will be some resistance but continue to pull gently. The clip is located right underneath the audio jacks.
  • Remove the clip located on the backside of the audio jack housing by gently pulling it out.

  • There will be some resistance but continue to pull gently.

  • The clip is located right underneath the audio jacks.

Yorum Ekle

Remove the screw that connects the black wire of the tone arm to the base of the audio jack housing. Remove the screw that connects the black wire of the tone arm to the base of the audio jack housing. Remove the screw that connects the black wire of the tone arm to the base of the audio jack housing.
  • Remove the screw that connects the black wire of the tone arm to the base of the audio jack housing.

Yorum Ekle

Mac RAM Kitleri
Mac'inizi hızlandırın. Hafızasını en yükseğe çıkar.
Mac RAM Kitleri
Mac'inize daha fazla bellek alın.
Gently pull the wire that you just unscrewed to release it from the clip. Gently pull the wire that you just unscrewed to release it from the clip.
  • Gently pull the wire that you just unscrewed to release it from the clip.

Yorum Ekle

Remove the two screws connecting the circuit board to the tone arm. Remove the two screws connecting the circuit board to the tone arm. Remove the two screws connecting the circuit board to the tone arm.
  • Remove the two screws connecting the circuit board to the tone arm.

Yorum Ekle

Remove the two remaining screws connecting the tone arm to the device. Remove the two remaining screws connecting the tone arm to the device.
  • Remove the two remaining screws connecting the tone arm to the device.

Yorum Ekle

Flip the turntable back over to the top side.
  • Flip the turntable back over to the top side.

  • Remove the counter weight located at the back of the tone arm.

Yorum Ekle

Push out the pin keeping the tone arm in place using a Phillips #00 screwdriver. Once you have pushed the pin out with the screwdriver, pull the rest of it out using your hand. Once you have pushed the pin out with the screwdriver, pull the rest of it out using your hand.
  • Push out the pin keeping the tone arm in place using a Phillips #00 screwdriver.

  • Once you have pushed the pin out with the screwdriver, pull the rest of it out using your hand.

Yorum Ekle

Pick up the tone arm and point the back end of it towards its base. Push the back end of the tone arm into the hole. Flip the turntable over and pull the tone arm all the way through the hole.
  • Pick up the tone arm and point the back end of it towards its base.

  • Push the back end of the tone arm into the hole.

  • Flip the turntable over and pull the tone arm all the way through the hole.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Nikolai

Üyelik tarihi: 12-10-2011

161 İtibar

5 adet Kılavuz yazıldı

Takım

Cal Poly, Team 17-14, Regan Fall 2011 Cal Poly, Team 17-14, Regan Fall 2011 üyesi

CPSU-REGAN-F11S17G14

4 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 13

Son 30 Gün: 69

Her zaman: 4,275