Rexing V1P Plus Motherboard Replacement

Giriş

If your Rexing V1P Plus (also known as the Rexing V1P-4k) is not powering on, not displaying anything on the screen, or not recording audio, the device's motherboard may be damaged or faulty. This guide will walk you through how to replace the device's motherboard.

This replacement requires the removal of the device's battery. The battery on the Rexing V1P Plus does not hold a charge for long without being connected to a power source. To ensure the battery is safe to remove, leave the device unplugged for a short period to drain the battery of any charge it may have.

This replacement requires the use of a soldering iron. If you have no prior experience using a soldering iron, it is recommended to do some additional research to gain familiarity with using this tool.

Neye ihtiyacın var

Adım 1 Front Camera

Rexing V1P Plus Motherboard Replacement, Front Camera: adım 1, 3 resimden 1.

Rexing V1P Plus Motherboard Replacement, Front Camera: adım 1, 3 resimden 2.

Rexing V1P Plus Motherboard Replacement, Front Camera: adım 1, 3 resimden 3.

Begin by orienting the device with the LCD screen facing down.
Remove the four 6 mm screws, located on the backside of the device, using the Phillips #00 screwdriver.

Düzenle

Adım 2

Rexing V1P Plus Motherboard Replacement: adım 2, 3 resimden 3.

Remove the back cover of the device and place it to the side.
Rotate the device 180 degrees to where the camera is facing you.

Düzenle

Adım 3

Rexing V1P Plus Motherboard Replacement: adım 3, 3 resimden 3.

Remove the two 5 mm screws next to the lens using the Phillips #00 screwdriver.

Düzenle

Adım 4

Rexing V1P Plus Motherboard Replacement: adım 4, 3 resimden 3.

Remove the two camera angle adjusters from the side of the device and carefully pull out the lens.

Düzenle

Adım 5

Rexing V1P Plus Motherboard Replacement: adım 5, 3 resimden 3.

Remove the two 5mm screws securing the camera support bracket using the Phillips #00 screwdriver.

Düzenle

Adım 6

Rexing V1P Plus Motherboard Replacement: adım 6, 3 resimden 3.

Carefully remove the plastic frame piece from its previously secured position on the motherboard.
It will rest loosely around the white camera ribbon.
Rotate the device 180 degrees to where the camera is facing away from you.

Düzenle

Adım 7

Rexing V1P Plus Motherboard Replacement: adım 7, 3 resimden 3.

Carefully peel back the adhesive material covering the ribbon cable connection.

Düzenle

Adım 8

Rexing V1P Plus Motherboard Replacement: adım 8, 3 resimden 3.

Using the Flathead 1.5mm screwdriver, or another pry tool, gently flip up the black ZIF connector locking flap to free the ribbon cable.
Once the connector is open, slide the ribbon cable out to remove it.

Düzenle

Adım 9 Motherboard

Rexing V1P Plus Motherboard Replacement, Motherboard: adım 9, 3 resimden 1.

Rexing V1P Plus Motherboard Replacement, Motherboard: adım 9, 3 resimden 2.

Rexing V1P Plus Motherboard Replacement, Motherboard: adım 9, 3 resimden 3.

Using a soldering iron, disconnect the four wires connected to the motherboard.

Düzenle

Adım 10

Rexing V1P Plus Motherboard Replacement: adım 10, 3 resimden 3.

Using the Phillips #00 screwdriver, remove the three 3.5 mm screws securing the motherboard to the case.

Düzenle

Adım 11

Rexing V1P Plus Motherboard Replacement: adım 11, 3 resimden 3.

Pull the black antenna wire with the gold cap straight up to disconnect it from the motherboard.
Using your fingers, spread the case apart to provide space for the motherboard to be removed.
This must be done to free the connected ports from their mounting locations in the case.