Shark Navigator Lightweight Upright Motherboard Replacement

Giriş

The motherboard is the command center for the vacuum's functions. Sometimes components on the board will come loose and require replacement. This guide will show you the steps necessary to replace the motherboard.

Neye ihtiyacın var

Adım 1 Head Shell

Shark Navigator Lightweight Upright Motherboard Replacement, Head Shell: adım 1, 2 resimden 1.

Shark Navigator Lightweight Upright Motherboard Replacement, Head Shell: adım 1, 2 resimden 2.

Detach the hose connected on the bottom of the vacuum by pulling it out of the casing.

Düzenle

Adım 2

Lay the vacuum on its side.
Press in the black, rubberish button located on the back of the vacuum to detach the vacuum head from the body.

Düzenle

Adım 3

Flip over the vacuum head so the brush head is facing up.

Düzenle

Adım 4

Shark Navigator Lightweight Upright Motherboard Replacement: adım 4, 3 resimden 3.

Remove the small front wheels with a metal spudger by inserting the metal spudger in front of the wheel and slowly prying up. This will free the wheel and reveal the screw beneath it.
Repeat this for the other wheel.

Düzenle

Adım 5

Remove the two 18mm screws with a JIS 1 screwdriver.

Düzenle

Adım 6

Remove the four 18mm screws located on the top corners and the bottom/middle of the vacuum head using a JIS 1 screwdriver.

Düzenle

Adım 7

Remove the two 18mm screws located on the inside of the large wheels using a JIS 1 screwdriver.

Düzenle

Adım 8

Shark Navigator Lightweight Upright Motherboard Replacement: adım 8, 3 resimden 3.

Remove the plastic cover by prying the plastic cover up using a plastic opening tool.
Prying in multiple locations may be necessary to create separation.

Düzenle

Adım 9 Motor

Shark Navigator Lightweight Upright Motherboard Replacement, Motor: adım 9, 1 resimden 1.

Locate the motor on the top right corner of the vacuum head shell.

Düzenle

Adım 10

Shark Navigator Lightweight Upright Motherboard Replacement: adım 10, 3 resimden 3.

Remove the belt from the motor gear by sliding the belt to the right.

Düzenle

Adım 11

Shark Navigator Lightweight Upright Motherboard Replacement: adım 11, 3 resimden 3.

Remove the white metal wire connector from the motor.
The white cable is positive.

Düzenle

Adım 12

Remove the black metal wire connector from the motor.
The black cable is negative.

Düzenle

Adım 13 Motherboard

Shark Navigator Lightweight Upright Motherboard Replacement, Motherboard: adım 13, 2 resimden 1.

Shark Navigator Lightweight Upright Motherboard Replacement, Motherboard: adım 13, 2 resimden 2.

Remove the two 12mm screws using a JIS 1 screwdriver.

Düzenle

Adım 14

Remove the wire housing by removing one 12mm screw using a JIS 1 screwdriver.

Düzenle

Adım 15

Bu adımda kullanılan alet:

Tweezers

$4.99

Satın Al

Lift up the wire housing from the plastic base using tweezers.

Düzenle

Adım 16

Free the black and white cables that were previously attached to the motor from their slot.

Düzenle

Adım 17

Free the motherboard and its connecting parts from the rest of the vacuum.
Turn the motherboard upside-down and spread wires out.

Düzenle

Adım 18

Heat the wire connection's solder joint until the joint looks wet and liquidy.
While maintaining contact with the solder iron, free the wire end by pulling the wire away from the board with the tweezers.
For instructions on how to solder properly please refer to this soldering technique guide. How To Solder and Desolder Connections
Remember which cables were soldered onto where. You will have to re-solder the cables back onto the same joint.
Solder iron is extremely hot and should be handled with care. Always wear eye protection when soldering.