Eşyalarını Tamir Et Topluluk Mağaza

Unbranded UB-15MS10 Speaker Replacement

Arşivlenmiş Kılavuz
Bu kılavuz sadece arşivsel amaçlarla muhafaza edilmiştir. Onarımınızı gerçekleştirmek için kılavuzun güncel halini kullanın.

Giriş

This guide walks you through how to replace a broken speaker on your UnBranded Tablet.

Neye ihtiyacın var

  1. Unbranded UB-15MS10 Speaker Replacement, Back Panel: adım 1, 1 resimden 1.

    • Remove the cover over the Micro SD outlet by using a plastic opening tool to pry open and push out the cover panel.

    Düzenle

  2. Unbranded UB-15MS10 Speaker Replacement: adım 2, 1 resimden 1.

    • Remove the two 4-mm #0 screws from the inside of the Micro SD compartment.

    Düzenle

  3. Unbranded UB-15MS10 Speaker Replacement: adım 3, 2 resimden 1. Unbranded UB-15MS10 Speaker Replacement: adım 3, 2 resimden 2.

    • Insert blue guitar picks in the crease between the top and bottom panels starting on the same end as the Micro SD slot.

    • Inserting the picks directly under the Micro SD compartment was the easiest place to get started. It still requires some force.

    Düzenle

  5. Unbranded UB-15MS10 Speaker Replacement: adım 4, 1 resimden 1.

    • Insert the black spudger between the guitar picks in order to pry open gaps between the blue guitar picks.

    • As the gaps open, slide the guitar picks along the sides to separate the panels.

    Düzenle

  6. Unbranded UB-15MS10 Speaker Replacement: adım 5, 1 resimden 1.

    • Pry all four sides apart using the blue guitar picks and the black spudger until they can easily be pried apart by hand.

    Düzenle

  7. Unbranded UB-15MS10 Speaker Replacement, Speaker: adım 6, 1 resimden 1.

    • Remove the yellow tape from the speaker.

    Düzenle

  8. Unbranded UB-15MS10 Speaker Replacement: adım 7, 1 resimden 1.

    • Remove the two 4-mm #0 screws holding the speaker in place.

    • The copper-colored plastic piece covering the speaker does not need to be removed from the device, move it to the side to reach the screws.

    Düzenle

  9. Unbranded UB-15MS10 Speaker Replacement: adım 8, 1 resimden 1.

    • Remove the silver tape covering the speaker's black and red wires.

    Düzenle

  10. Unbranded UB-15MS10 Speaker Replacement: adım 9, 1 resimden 1.

    • Reflow the solder of the black and red wires from the circuit board by using the soldering iron.

    • For more information about using a soldering iron click here.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

7 tane daha katılımcı ile

Jordan Turk

Üyelik tarihi: 09/21/15

331 İtibar

2 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

IUPUI, Team 2-1, Baechle Fall 2015 IUPUI, Team 2-1, Baechle Fall 2015 üyesi

IUPUI-BAECHLE-F15S2G1

3 Üyeler

3 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 720