2010 Scion tC Side Mirror Replacement 2 No'lu Adım Geçmişi

-	[* red] Now, grab your ratchet and attach the *10mm socket* ~~if not already done~~. Make sure the back of it is turned to *loosen* rather than tighten.
-	[* icon_reminder] ~~If you are not sure then and give it a few turns by hand and~~* if there is noise being made when rotated up, that is tightening*. ~~If that happens, then go ahead and turn~~ the knob at the back to change ~~this~~ to loosening.
-	[* black] ~~Once~~ the ratchet ~~is set up, place it~~ on one of the bolts and start rotating the ratchet down then up to loosen each nut. ~~You'll know you are doing it right if clicking noises happen when you rotate down and no noise is happening when you move up, you're going to continue this motion until the~~ nut is loose.
-	[* icon_note] *Note*: ~~Make sure to hang on to~~ each nut ~~as they~~ will be needed for the new mirror ~~you will be placing on~~. Also, ~~make sure that~~ when ~~loosening~~ the last nut, ~~to have someone or your free hand hang on to~~ the mirror as it ~~will become loose and probably fall down~~.
+	[* red] Now, grab your ratchet and attach the *10mm socket. Make sure the back of it is turned to loosen* rather than tighten.
+	[* icon_reminder] * if there is noise being made when rotated up, that is tightening*. Turn the knob at the back to change to loosening.
+	[* black] Place the ratchet on one of the bolts and start rotating the ratchet down then up to loosen each nut. After each nut is loose remove them by hand.
+	[* icon_note] *Note*: Keep each nut . They will be needed for the new mirror. Also, when removing the last nut, hold the mirror to prevent it from falling.

-	[* red] Now, grab your ratchet and attach the *10mm socket* ~~if not already done~~. Make sure the back of it is turned to *loosen* rather than tighten.
-	[* icon_reminder] ~~If you are not sure then and give it a few turns by hand and~~* if there is noise being made when rotated up, that is tightening*. ~~If that happens, then go ahead and turn~~ the knob at the back to change ~~this~~ to loosening.
-	[* black] ~~Once~~ the ratchet ~~is set up, place it~~ on one of the bolts and start rotating the ratchet down then up to loosen each nut. ~~You'll know you are doing it right if clicking noises happen when you rotate down and no noise is happening when you move up, you're going to continue this motion until the~~ nut is loose.
-	[* icon_note] *Note*: ~~Make sure to hang on to~~ each nut ~~as they~~ will be needed for the new mirror ~~you will be placing on~~. Also, ~~make sure that~~ when ~~loosening~~ the last nut, ~~to have someone or your free hand hang on to~~ the mirror as it ~~will become loose and probably fall down~~.
+	[* red] Now, grab your ratchet and attach the *10mm socket. Make sure the back of it is turned to loosen* rather than tighten.
+	[* icon_reminder] * if there is noise being made when rotated up, that is tightening*. Turn the knob at the back to change to loosening.
+	[* black] Place the ratchet on one of the bolts and start rotating the ratchet down then up to loosen each nut. After each nut is loose remove them by hand.
+	[* icon_note] *Note*: Keep each nut . They will be needed for the new mirror. Also, when removing the last nut, hold the mirror to prevent it from falling.