Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Giriş

This guide shows how to apply display assembly adhesive to an opened iPad.

Parçalar

Hiçbir parça belirtilmedi.

  1. Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue. Use tweezers to pull up sections of tape residue.
    • Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue.

    • Use tweezers to pull up sections of tape residue.

    • Use an opening tool or a spudger to scrape residue off. You can use high concentration (over 90%) isopropyl alcohol to soften the adhesive.

    • Remove the residue by wiping in one direction to prevent smearing.

    • Do not scrape with a metal tool, or you will scratch the display assembly's surface.

  2. Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.
    • Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.

  3. Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom. Peel and remove the topmost plastic cling layer from the left adhesive strip.
    • Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom.

    • Peel and remove the topmost plastic cling layer from the left adhesive strip.

    • Peel and remove the bottom plastic liner from the strip.

    • The top of the adhesive strip should still be covered by a colored plastic layer as well as a clear plastic stiffening layer.

    • The bottom of the adhesive strip should now be exposed and sticky.

  4. If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now. If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now.
    • If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now.

  5. LCD iPhone Ekran Tamir Kit'leri

    Ömür Boyu Garantimiz kapsamındaki bütçe seçeneği.

    Shop Kits

    LCD iPhone Ekran Tamir Kit'leri

    Onarım maliyetlerini düşürün, kaliteyi değil.

    Shop Kits
  6. Align the left adhesive strip to the left edge of the display assembly. Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place. Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place.
    • Align the left adhesive strip to the left edge of the display assembly.

    • Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place.

  7. Repeat the process with the right adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner layer from the strip.
    • Repeat the process with the right adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner layer from the strip.

    • Align the adhesive strip to the right edge of the display assembly.

    • Starting from one corner, lay the adhesive strip onto the display assembly and press in place.

  8. Repeat the process for the top adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner from the strip.
    • Repeat the process for the top adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner from the strip.

    • Align the strip to the top of the display assembly such that the straight adhesive line bridges the gap between the left and right strips.

    • Press the strip in place.

  9. Peel and remove the clear plastic stiffening layer from all three adhesive strip sections. The adhesive strips should still be covered by colored plastic liners. The adhesive strips should still be covered by colored plastic liners.
    • Peel and remove the clear plastic stiffening layer from all three adhesive strip sections.

    • The adhesive strips should still be covered by colored plastic liners.

  10. Continue with the reassembly process until you are ready to seal the device.
    • Continue with the reassembly process until you are ready to seal the device.

  11. Peel and remove the three colored plastic liners to expose the adhesive. Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond. Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond.
    • Peel and remove the three colored plastic liners to expose the adhesive.

    • Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond.

Sonuç

Repair didn’t go as planned? Check out our Answers Community for troubleshooting help.

5 farklı kişi bu kılavuzu tamamladı.

Arthur Shi

Üyelik tarihi: 03-01-2018

94.711 İtibar

280 adet Kılavuz yazıldı

Takım

iFixit iFixit üyesi

Community

111 Üyeler

10.660 adet Kılavuz yazıldı

Bir Yorum

Thanks, I was able to fix my wife’s shattered digitizer screen on the iPad 6th gen with this guide!

Kevin Chatterton II - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 29

Son 7 gün: 168

Son 30 gün: 594

Her zaman: 3,139