Ana içeriğe geç
Yardım

Google Pixel 7 Pro Battery Replacement için Bekleyen Düzenlemeler

IT

Not: Bu adım ya da girişe yapılmış herhangi bir düzenlemeyi kabul etmek ya da reddetmek, daha önceden yapılmış ve beklemekte olan diğer bütün düzenlemelere dolaylı olarak uygulanır.

#4. adım düzenlendi: [Adım düzenlendi]

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

Başlık How to remove a stuck battery
0-icon_note-Follow this step if you couldn't loosen the battery using the battery release strip.
0-black-Apply a few drops of high concentration (90% or higher) isopropyl alcohol into the gap at the top edge of the battery.
1-icon_caution-Don't apply too much alcohol, or you'll loosen the NFC antenna and charging coil underneath the battery.
1-black-Wait about one minute for the alcohol solution to weaken the adhesive.
0-black-Use the flat end of a spudger or an opening pick to gently lift the top edge of the battery until you can grab it with your fingers.
1-icon_note-Don't use excessive force on the battery. Slow, consistent pressure is all that's required to free it from the frame.
1-icon_caution-Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.
+[title] Come rimuovere un batteria incollata
+[* icon_note] Segui questo passaggio se non riesci ad allentare la batteria usando la striscia di rilascio della batteria.
+[* black] Applica alcune gocce di alcol isopropilico ad alta concentrazione (90% o superiore) nello spazio sul bordo superiore della batteria.
+ [* icon_caution] Non applicare troppo alcol, altrimenti allenterai l'antenna NFC e l'avvolgimento di ricarica sotto la batteria.
+ [* black] Attendi circa un minuto affinché la soluzione alcolica indebolisca l'adesivo.
+[* black] Usa l'estremità piatta di uno spudger o un plettro di apertura per sollevare delicatamente il bordo superiore della batteria finché non riesci ad afferrarla con le dita.
+ [* icon_note] Non usare eccessiva forza sulla batteria. Una pressione lenta e costante è tutto ciò che serve per liberarla dal telaio.
+ [* icon_caution] Fai attenzione a non forare o piegare la batteria con il tuo utensile: una batteria forata o piegata potrebbe perdere sostanze chimiche pericolose o causare un incendio.


#5. adım düzenlendi: [Adım düzenlendi]

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

Başlık Remove the battery
0-black-Tilt the battery out of the device to separate the rest of the adhesive.
0-black-Remove the battery.
0-icon_caution-Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard.
0-icon_reminder-To secure the replacement battery:
1-black-[guide|113604|Apply pre-cut adhesive adhesive|new_window=true] or double-sided tape to the battery well at the places where the old adhesive was located, not directly onto the battery.
1-black-Temporarily reconnect the battery to the motherboard to help align it correctly. Disconnect the battery after it's seated.
1-black-Make sure that the battery sits in the center of the battery well and there's an even gap around the battery.
1-black-Press the new battery firmly into place.
+[title] Rimuovi la batteria
+[* black] Inclina la batteria fuori dal dispositivo per separare il resto dell'adesivo.
+[* black] Rimuovi la batteria.
+[* icon_caution] Non reinstallare una batteria danneggiata o deformata, in quanto rappresenta un potenziale pericolo per la sicurezza.
+[* icon_reminder] Per fissare la batteria sostitutiva:
+ [* black] [https://it.ifixit.com/Guida/Come+usare+un+foglio+di+adesivo+pretagliato/113604|Applica l'adesivo pre-tagliato|new_window=true] o il nastro biadesivo al vano della batteria nei punti in cui si trovava il vecchio adesivo, non direttamente sulla batteria.
+ [* black] Ricollega temporaneamente la batteria alla scheda madre per aiutare l'allineazione corretta. Scollega la batteria dopo averla posizionata.
+ [* black] Assicurarti che la batteria sia posizionata al centro del vano della batteria e che ci sia uno spazio uniforme attorno alla batteria.
+ [* black] Premi saldamente la nuova batteria in posizione.


#3. adım düzenlendi: [Adım düzenlendi]

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

Başlık Separate the battery's adhesive
0-black-Grip the pull tabs, and slide it up until you can feel it contact adhesive underneath.
0-black-Lift straight up to pull the battery away from its adhesive.
1-icon_note-Work slowly. It's easy to lose your grip and accidentally pull the tab up from under the battery. It can be helpful to use gloves for more grip.
1-icon_note-If you're having difficulty separating the adhesive, apply more heat and wait for the adhesive to loosen.
1-black-If available, have a friend help hold the phone down while you lift.
0-icon_note-If you lose or tear the release strip, or the adhesive is too strong, ***follow the next step for an alternative method***.
+[title] Separa l'adesivo della batteria
+[* black] Afferra le linguette e falle scorrere verso l'alto finché non senti che toccano l'adesivo sottostante.
+[* black] Sollevala verso l'alto per staccare la batteria dall'adesivo.
+ [* icon_note] Lavora lentamente. È facile perdere la presa e tirare accidentalmente la linguetta da sotto la batteria. Può essere utile usare dei guanti per una presa migliore.
+ [* icon_note] Se hai difficoltà a staccare l'adesivo, applica più calore e attendi che l'adesivo si allenti.
+ [* black] Se disponibile, chiedi a un amico di aiutarti a tenere fermo il telefono mentre lo sollevi.
+[* icon_note] Se perdi o strappi la striscia di rilascio o se l'adesivo è troppo forte, ***segui il passaggio successivo per un metodo alternativo***.


#2. adım düzenlendi: [Adım düzenlendi]

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

Başlık Separate the battery pull tabs
0-black-Use [product|IF145-020|tweezers], or your fingers, to peel the plastic pull tabs away from the battery.
+[title] Separa le linguette della batteria
+[* black] Utilizza delle [product|IF145-020|pinzette|new_window=true] o le dita per staccare le linguette di estrazione in plastica dalla batteria.


#1. adım düzenlendi: [Adım düzenlendi]

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

Başlık Heat the battery's adhesive
0-black-Apply a [https://www.ifixit.com/Guide/iOpener+Heating/25705|heated iOpener|new_window=true] to the back of the device to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes.
1-icon_note-A hair dryer, [link|https://www.ifixit.com/Guide/How+to+Use+a+Heat+Gun+to+Soften+Adhesive/151116|new_window=true|heat gun], or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch.
+[title] Scalda l'adesivo della batteria
+[* black] Applica un [https://it.ifixit.com/Guida/Riscaldamento+iOpener/25705|iOpener riscaldato|new_window=true] sul retro del dispositivo per allentare l'adesivo sottostante. Applica l'iOpener per almeno 3 minuti.
+ [* icon_note] Puoi utilizzare anche un asciugacapelli, una [https://it.ifixit.com/Guida/Come+usare+una+pistola+termica+per+ammorbidire+l%27adesivo/151116|pistola termica|new_window=true] o una piastra riscaldante, ma fai attenzione a non surriscaldare il dispositivo. Il bordo dovrebbe risultare leggermente troppo caldo al tatto.


Giriş düzenlendi

Acn0w (14,3b) tarafından düzenlendi

(Bu düzenlemeyi denetlemek için yeterli itibarınız yok.)

Kaynak Metin

şey Battery
Başlık Google Pixel 7 Pro Battery Replacement
Giriş ***This repair guide was authored by the iFixit staff and hasn’t been endorsed by Google. Learn more about our repair guides [[Info:content-quality|here|new_window=true]].*** Use this guide to replace the battery in your Google Pixel 7 Pro. Note: this guide was made using the ***GE2AE*** model, which features a 5G mmWave antenna. If you have a non-mmWave model, you can still use this guide—just ignore the mmWave antenna steps. ***For your safety, discharge the battery below 25% before disassembling your phone.*** This reduces the risk of fire if the battery is accidentally damaged during the repair. If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]]. Caution: The Pixel 7 Pro contains class 1 lasers. Disassembly could result in exposure to invisible infrared laser emissions. Retaining water resistance after the repair will depend on how well you reapply the adhesive, but your device will lose its IP (Ingress Protection) rating. You'll need replacement adhesive in order to complete this repair.
Sonuç Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before you install it. ***To reassemble your device, follow these instructions in reverse order.*** For optimal performance, [[Battery Calibration|calibrate your newly installed battery|new_window=true]] after completing this guide. To run a diagnostics test with the built-in Pixel Diagnostic tool, [document|32396|click here]. Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]]. Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers/Ask/Google+Pixel+7+Pro|Google Pixel 7 Pro answers community] for help.
Thing
Batteria
Title
Sostituzione Batteria Galaxy Pixel 7 Pro
Introduction
***Questa guida di riparazione è stata creata dallo staff di iFixit e non è stata approvata da Google. Scopri di più sulle nostre guide alla riparazione [[Info:content-quality|qui|new_window=true]].***
Segui questa guida per sostituire la batteria del tuo Google Pixel 7 Pro.
Nota: questa guida è stata realizzata utilizzando il modello ***GE2AE***, che presenta un'antenna mmWave 5G. Se hai un modello non mmWave, puoi comunque utilizzare questa guida, ignorando semplicemente i passaggi dell'antenna mmWave.
***Per la tua sicurezza, scarica la batteria sotto il 25% prima di smontare il telefono.*** Ciò riduce il rischio di incendio se la batteria viene accidentalmente danneggiata durante la riparazione. Se la batteria è gonfia, [[What to do with a swollen battery|prendi le precauzioni appropriate|new_window=true]].
Attenzione: Pixel 7 Pro contiene laser di classe 1. Lo smontaggio potrebbe causare l'esposizione a emissioni laser a infrarossi invisibili.
Il mantenimento della resistenza all'acqua dopo la riparazione dipenderà da quanto bene riapplicherai l'adesivo, ma il tuo dispositivo perderà la sua classificazione IP (Ingress Protection).
Per completare questa riparazione avrai bisogno di adesivo sostitutivo.
Conclusion
Confronta il tuo nuovo pezzo di ricambio con quello originale: potresti dover trasferire i componenti rimanenti o rimuovere i supporti adesivi dal nuovo pezzo prima di installarlo.
***Per riassemblare il dispositivo, segui le istruzioni nell'ordine inverso.***
Per prestazioni ottimali, [[Battery Calibration|calibra la batteria appena installata|new_window=true]] dopo aver completato questa guida.
Per eseguire un test diagnostico con lo strumento Pixel Diagnostic integrato, [document|32396|clicca qui].
Porta i tuoi rifiuti elettronici a un [[E-Waste|R2 o a un riciclatore certificato e-Stewards|new_window=true]].
La riparazione non è andata come previsto? Prova alcuni [[Troubleshooting Problems After a Repair|risoluzione dei problemi di base]] o chiedi aiuto alla nostra [link|https://www.ifixit.com/Answers/Ask/Google+Pixel+7+Pro|Comunità Risposte di Google Pixel 7 Pro].