Device does not turn on
You are having trouble getting your calculator to turn on.
Battery is not working
If your device battery is dead or low, you will need to replace it. TI-36X Pro Battery Replacement gives instructions on how to replace the battery of a TI-36X Pro.
Screen is dim
If your screen is set to a low contrast, it may seem like your device is off. Look closely for faint characters or a flashing cursor on the screen. To raise the contrast, press and release the "2nd" button and then press the "+" button. Do this several times to raise the contrast to a higher level. (You can lower the contrast by pressing and releasing the "2nd" button and then pressing the "-" button).
The display is hard to read
Characters on the display of your calculator are very faint or not present at all.
Bad room lighting or viewing angle
Different types of lighting and viewing angles can make the screen appear to be very dim. Try tilting the device or changing your current lighting to see if the screen becomes easier to read.
Contrast may be too low or too high
A very high high or low display contrast can make the screen hard to read. To adjust display contrast press and release the 2nd key and then press the + button to darken screen and the - button to brighten the screen.
Low Battery
If the batteries to your deice are low, then your screen may appear dim. To replace the batteries try our TI-36X Pro Battery Replacement Guide.
Broken solar panel
The solar panel provides some power to the screen. If it is broken, the screen might appear dim and hard to read. TI-36X Pro Solar Panel Replacementgives instructions on replacing the solar panel.
Dysfunctional Buttons
The buttons of your calculator don't work.
Dim Screen
Having a dim screen can make it hard to see if the buttons are doing anything. Make sure that you can clearly see a flashing cursor. If not, you may need to adjust the contrast or your viewing angle.
Stuck buttons
Sometimes, having one button stuck will make the other buttons unresponsive. Make sure that there are no buttons stuck underneath your front panel.
The calculator needs to be reset
Sometimes you will need to reset your calculator to make it work. Try turning it off and on again. If the problem is unsolved, or you are unable to use the power button, read this guide to learn how to fully reset your calculator.
Buttons broken or out of alignment
If broken of misaligned, the buttons will not work properly. You can follow TI-36X Pro Button Replacement Guide to replace a broken button.
Turn calculator off and on. If problem continues, check to see if any buttons are stuck or partially pressed. Next, check to make sure that the screen is working. Screen is working properly if there is a flashing cursor displayed.
Display is visible, but not working
Display is visible, but unresponsive.
Reset the calculator
Resetting the calculator can solve many problems. Following this guide will show you how to fully reset your device. Caution: Resetting your calculator will delete your history of equations.
The calculator is stuck in another language or an unusable mode
''Calculator is stuck in another language that you can't read."
Software reset needed
Resting the calculator's software will wipe all memory and return it to factory settings. To reset your calculator, place it face-down on a flat surface. Use a pen or pencil to press and hold the small, silver button located at the base of the calculator for 1 second. Turn the calculator over; your screen should read "MEMORY CLEARED." Press the "clear" button and your calculator should be back to normal.
Ekip
Cal Poly, Team 11-52, Amido Spring 2014 Cal Poly, Team 11-52, Amido Spring 2014 üyesi
CPSU-AMIDO-S14S11G52
4 Üyeler
10 adet Kılavuz yazıldı
17 Yorum
error — integral Cos(π x) dx range 0 to .5 I get .499937368 —- I should get 1/π or .318309886
can anyone confirm error or tell what I did wrong
Raymond Low - Yanıt
You’re in degree mode when you want to be in radians.
George -
I have a problem with my TI-36X II , when i turn it on i see the clock symbol in the 1st line and -8/ in the 2nd line and its blinking , can u help me ?
akaveljko - Yanıt
SYNTAX ERROR TI-36X Pro
When I enter the following I always get a SYNTAX ERROR message but it is NOT a
syntax error.. wont let me put special characters in so i’ll do it this way..
(-2)sq + 3 (-2) -7 Press enter answer should be -9
but I always get SYNTAX ERROR
For a better explanation https://www.youtube.com/watch?v=6At4l9tH...
Kelley enters (-2)sq + 3 (-2) -7 Presses enter answer should is -9
Any help or suggestions appreciated.. Thanks John
akie hara - Yanıt
If you enter a negative number using the subtract key, it will always give you a syntax error.
There is a difference between the subtract key and the negative key.
The negative 2 is entered with the negative key in the lower right (under the 3).
The subtract 7 is entered with the normal subtract key.
You can get bit the same way if you enter negative numbers in any of the solvers using the subtract key instead of the correct one.
trojdor -
i get syntax error also
Tess Obert - Yanıt
Sir I insert the battery , close the cover then it will start sometimes after few seconds automatically off , then how to start the calculator
Rajshekhar S D - Yanıt
My calculator gives the wrong answer. When I square a negative number, it gives me a negative answer. For example, if I square -2, it says that the answer is -4, even though the correct answer is 4. Is there a way to fix that?
Rana - Yanıt
Yes. Put the negative number in parenthesis, then square that quantity. The order of operations prioritizes the exponent (over the minus sign), and does the square part first….then adds the minus sign later/after. You have to surround the negative number and sign in parenthesis to tell the calculator to square the negative number. (And yes, it’s kind of annoying.)
trojdor -
how to exit overflow error screem
Olsenjr MOUELE - Yanıt
i input sin1 and i get .01745… changing from degrees or radians does not change the issue of outputting the same number
juicedsupra1 - Yanıt
Some horizontal pixel lines are missing
Dhruv Varshney - Yanıt
To reset as well, press 2nd + clear + on button. If I leave mine out on the desk without covering it or turning it over to keep the panel from seeing anything for whatever reason, the calculator with turn on then turn itself off and it won’t turn back on until I reset it like this and it clears the memory which is annoying to change my mode settings back every time. So I generally try to remember to set it down face down or cover it.
Ryan - Yanıt
How do I find a square root? I get Domain Error message.
E.J. Abell - Yanıt
The Mod(14,2) result as unsupported operation
Endika A - Yanıt
My calculator is stuck on a screen that shows the last calculation I did and a line under it that goes straight across with a long decimal number under that. None of my buttons are working and the software reset didn't do anything either. I've tried waiting out a little to see if it at least turns off but so far there's nothing. Any ideas?
Hannah DeSouza - Yanıt
When I try to do integrals I get "fnInt(" on the screen, but all the videos I've watched on it show an actual integral that you fill out. Is it malfunctioning?
tj weiler - Yanıt