Eşyalarını Tamir Et Topluluk Mağaza

ANKER SoundCore Charging Port Replacement

Giriş

If your ANKER SoundCore does not charge, your charging port may be broken. If you wish to replace your device’s charging port, you can follow this step-by-step guide.

Before attempting to replace anything, it is recommended that you look at this device’s troubleshooting guide.

You will need an iFixit opening tool, Phillips #0 screwdriver, metal spludger, and iFixit opening pick. Soldering experience is needed.

Neye ihtiyacın var

  1. ANKER SoundCore Charging Port Replacement, Charging Port: adım 1, 3 resimden 1. ANKER SoundCore Charging Port Replacement, Charging Port: adım 1, 3 resimden 2. ANKER SoundCore Charging Port Replacement, Charging Port: adım 1, 3 resimden 3.

    • Use the plastic opening tool to pry off the screen.

    • Remove the screen from the device.

    Düzenle

  2. ANKER SoundCore Charging Port Replacement: adım 2, 1 resimden 1.

    • Remove the eight 10 mm Phillips #0 screws from the speaker mount.

    Düzenle

  3. ANKER SoundCore Charging Port Replacement: adım 3, 2 resimden 1. ANKER SoundCore Charging Port Replacement: adım 3, 2 resimden 2.

    • Use the metal spludger to pry off speaker mount.

    Düzenle

  5. ANKER SoundCore Charging Port Replacement: adım 4, 1 resimden 1.

    • Remove the two 8mm Phillips #0 screws from the circuit board.

    Düzenle

  6. ANKER SoundCore Charging Port Replacement: adım 5, 2 resimden 1. ANKER SoundCore Charging Port Replacement: adım 5, 2 resimden 2.

    • Carefully remove the circuit board from the speaker body.

    Düzenle

  7. ANKER SoundCore Charging Port Replacement: adım 6, 2 resimden 1. ANKER SoundCore Charging Port Replacement: adım 6, 2 resimden 2.

    • Use the iFixit Opening Pick to pry off the charging port cover.

    • Remove the charging port cover.

    Düzenle

  8. ANKER SoundCore Charging Port Replacement: adım 7, 2 resimden 1. ANKER SoundCore Charging Port Replacement: adım 7, 2 resimden 2.

    • Desolder the charging port from the circuit board.

    • Solder a new charging port in place of the old one.

    • For help soldering and desoldering, follow this guide.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

3 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

Briana Kuo

Üyelik tarihi: 02/10/20

311 İtibar

1 Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

Cal Poly, Team S22-G1, Regan Winter 2020 Cal Poly, Team S22-G1, Regan Winter 2020 üyesi

CPSU-REGAN-W20S22G1

5 Üyeler

6 adet Kılavuz yazıldı

4 Yorum

Where can I find a replacement port that is compatible?

tommy2197 - Yanıt

Where can I find a replacement port that is compatible?

Mike - Yanıt

The Charging port is an USB Mirco Port. To find right part search for JBL FLIP 3 on ebay or other platforms. It is the same part as used for the Anker SoundCore.

Agi -

Hi I have a Anker soundcore motion plus, the charging port is loose and not charging, it's a usb c, where can I buy that replacement part

.thanks

Justin - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 4

Son 7 gün: 31

Son 30 gün: 150

Her zaman: 10,166