Admiral AGD4675YQ3 Drum Belt Replacement

Clayton Biehunko ve başka bir katkıda bulunan

En son December 18, 2023 tarihinde güncellendi

30 dakika - 1 saat

Orta

Giriş

The unthinkable has happened. Your AGD4675YQ3 Admiral Dryer won't turn! The wet clothes are starting to stink and every company you call says the earliest they can get someone out there is 3 days away. Not to worry friends, the dryer is a much simpler machine than you might think. The most likely culprit is your dryer belt has fallen off its axel or snapped. With this guide, you will be back to finishing laundry day in no time. Bonus: You will also have newfound mechanical knowledge to brag to your friends about!

Neye ihtiyacın var

iFixit bu bağlantılar üzerinden satın aldığınızda komisyon kazanır.

Adım 1 Drum Belt

Admiral AGD4675YQ3 Drum Belt Replacement, Drum Belt: adım 1, 1 resimden 1.

Unplug the dryer's power cord.

Düzenle

Adım 2

Remove the lint catcher.

Düzenle

Adım 3

When removing the screws, ensure that they do not fall into the lint chute. If this happens, a deeper disassembly will be required that this guide does not cover.
Use your Phillips #1 screwdriver and remove both 25.4 mm Phillips #1 screws.

Düzenle

Adım 4

While keeping to the right corner, slip the butter knife in the slit above the dryer door.
If you cannot push the butter knife in, you are likely hitting the clip. Simply move the knife a bit more to the left till it slips in deep.
Pry up with moderate force and the clip holding the lid will pop up.
Repeat on the left side.

Düzenle

Adım 5

Fully lift the lid so that it stays in an upright position.

Düzenle

Adım 6

Disconnect the electrical harness on the right side.

Düzenle

Adım 7

Remove the 18.4 mm hex cap screws on the left and right side with the 8 mm socket wrench.
Remove the clips underneath the screws on the left and right side.

Düzenle

Adım 8

Using your thumb to hold the drum in place, pull the front panel of the dryer away from the drum.
There are two clips in the bottom left and right sides that will pop out when you pull.
Set the front panel to the side.

Düzenle

Adım 9

Place a shoebox sized item under the drum to hold the drum in place.
Keep the item as far to the left as possible so you will have room to work on the assembly underneath, located on the right.

Düzenle

Adım 10

Admiral AGD4675YQ3 Drum Belt Replacement: adım 10, 3 resimden 3.

If your drum belt has snapped, you can just pull the old belt out and proceed to step 13.
Grip the pulley bar and squeeze to push the pulley away from the drum.
Pull the belt off of the gear.

Düzenle

Adım 11

Remove the belt from the drum.

Düzenle

Adım 12

Place the new belt around the drum.
Make sure the grooved part of the belt is facing the grooved part of the drum.
The serial number and other identifying information on the belt should be facing up.

Düzenle

Adım 13

Admiral AGD4675YQ3 Drum Belt Replacement: adım 13, 3 resimden 3.

Form a loop with the belt and pull the loop under the pulley.
Squeeze the pulley bar and place the loop around the gear.

Düzenle

Adım 14

Rotate the drum counter clockwise and ensure the belt is covering the drum groove all the way around.
If the belt is out of place, simply tap it into place with your fingertips.

Düzenle