Tezgahım

Cihazların için kılavuz, parça ve yanıtlara hızlı erişim edin

Dünyanın en büyük onarım topluluğuna katılın

Parçalar

Kılavuzlar Cevaplar

Kingston HyperX Cloud II Microphone Wire Repair

Kingston HyperX Cloud II Microphone Wire Repair

Daniel Olaoluwa Ajagbonna ve 3 diğer katkıda bulunanlar

En son November 26, 2024 tarihinde güncellendi

25 dakika

Zor

Giriş

If your Kingston HyperX Cloud II microphone is having connection issues, use this guide to replace or reconnect your microphone wire to the driver. Inside the driver, the red wire is the wire that must be soldered to the driver for the microphone to be repaired. This problem occurs when the red wire gets disconnected from the speaker or stops working from natural causes.

Neye ihtiyacın var

Aletler

Daha fazlasını göster…

Adım 1 Kingston HyperX Cloud II Microphone Wire Repair

Kingston HyperX Cloud II Microphone Wire Repair, Kingston HyperX Cloud II Microphone Wire Repair: adım 1, 1 resimden 1.

Pulling along the edges, take off the padding.

Adım 2

Kingston HyperX Cloud II Microphone Wire Repair: adım 2, 2 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 2, 2 resimden 2.

Use a Phillips #0 screwdriver to remove the two 11 mm screws from the bracket support.

Adım 3

Kingston HyperX Cloud II Microphone Wire Repair: adım 3, 3 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 3, 3 resimden 2.

Kingston HyperX Cloud II Microphone Wire Repair: adım 3, 3 resimden 3.

Remove the inside bracket support and then remove the outside bracket support. Then set it to the side.
After removing the bracket support. Expand and remove the microphone speaker from the frame.

Adım 4

Kingston HyperX Cloud II Microphone Wire Repair: adım 4, 3 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 4, 3 resimden 2.

Kingston HyperX Cloud II Microphone Wire Repair: adım 4, 3 resimden 3.

Use a Phillips #1 screwdriver to remove the two 7.9 mm screws from the red support attached to the microphone speaker.

Adım 5

Kingston HyperX Cloud II Microphone Wire Repair: adım 5, 3 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 5, 3 resimden 2.

Kingston HyperX Cloud II Microphone Wire Repair: adım 5, 3 resimden 3.

Separate the red frame support from the microphone speaker by putting it to the side.

Adım 6

Kingston HyperX Cloud II Microphone Wire Repair: adım 6, 2 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 6, 2 resimden 2.

Remove the four 11 mm screws on the speaker frame with a Phillips #2 screwdriver.

Adım 7

Kingston HyperX Cloud II Microphone Wire Repair: adım 7, 3 resimden 1.

Kingston HyperX Cloud II Microphone Wire Repair: adım 7, 3 resimden 2.

Kingston HyperX Cloud II Microphone Wire Repair: adım 7, 3 resimden 3.

Remove the microphone speaker frame.
Open the microphone speaker to reveal circuitry.
Solder the detached red wire onto the driver.
Be cautious not to solder the wrong wire.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Daniel Olaoluwa Ajagbonna

Üyelik tarihi: 03/27/23

337 İtibar

2 adet Kılavuz yazıldı

+4 tane daha rozet

Ekip

IUPUI, Team 1-4, Harley Spring 2023 IUPUI, Team 1-4, Harley Spring 2023 üyesi

IUPUI-HARLEY-S23S1G4

3 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 13

Son 30 gün: 55

Her zaman: 1,351