Unplug your MacBook Air and power it off before you proceed.
  • Unplug your MacBook Air and power it off before you proceed.

  • Remove ten Phillips screws securing the lower case to the MacBook Air:

    • Six 2.8 mm screws

    • Two 3.8 mm screws

    • Two 5.4 mm screws

Yorum Ekle

Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.
  • Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

Yorum Ekle

  • Disconnect the battery connector by pulling it straight out of its socket.

Yorum Ekle

  • Remove the following nine screws securing the battery to the Air:

    • Four 2.9 mm Phillips.

    • Four 3.8 mm Phillips.

    • One 7.2 mm Phillips.

Yorum Ekle

  • Lift the battery out of the Air.

Yorum Ekle

  • Disconnect the port hatch ribbon cable from the logic board by pulling it straight up by its black pull tab.

  • Pull the audio out ribbon cable off the adhesive securing it to the upper case.

  • Use a spudger to pry the audio out ribbon cable connector board off the hard drive bracket.

I skipped the step (6c) of prying the audio out ribbon cable connector board off the hard drive bracket (& disconnecting it), since it doesn't come off real easily, and I didn't want to damage it. It only requires a little more care when removing the HD from it's bracket if you skip step 6c.

amiller770 - Yanıt

  • Disconnect the audio out cable from its socket on the port hatch ribbon cable.

This is not necessary and looks pretty risky too.

eugene_o - Yanıt

Agreed, I encountered no issues when I skipped this on a Rev.B model.

Kyle Milnes -

  • Use a spudger to pry the hard drive cable connector up off the logic board.

Reversing step 8 is where I ran into trouble. The replacement fan I had was slightly thicker than the original and caused the ZIF cable to work its way out of the tenuous connection it had to the SSD, resulting in a "?" missing boot drive error upon startup. Took me three tries to get it right! The difficulty is to get the drive connector to the logic board to reach and seat without pulling the other end out of the drive.

aaronmiller - Yanıt

  • Use the sharp end of a spudger to de-route the microphone cable from the hard drive bracket.

  • Remove the cosmetic screw cover from the adhesive securing it to the hard drive bracket.

Yorum Ekle

  • Remove the four Phillips screws securing the hard drive assembly to the upper case:

    • Two 4.7 mm screws.

    • Two 3.9 mm screws.

Longer screws on top.

Adam Nelson - Yanıt

Two 3.9 mm Phillips screws.

Two 4.7 mm Phillips screws.

Alvaro Hermida - Yanıt

There is a cable glued to the diskframe that must be loosened with a spudger before you can remove the frame.

oysteinalsaker - Yanıt

  • Lift the hard drive assembly out of the upper case.

Ever since Steve Jobs died, Apple hasn't been what it used to be.

George A. - Yanıt

  • Use the tip of a spudger to pull the fan cable connector straight away from its connector on the logic board.

Yorum Ekle

  • Use the tip of a spudger to move the cosmetic fan cover aside.

Yorum Ekle

  • If you have the original version of the MacBook Air (A1237), refer to picture 1. Remove the following screws securing the heat sink to the logic board:

    • One 5.9 mm Phillips screw.

    • Two 1.9 mm Phillips screws.

    • One 1.9 mm Phillips screw.

  • If you have the A1304 version of MacBook Air, refer to picture 2. Remove the following screws securing the heat sink to the logic board:

    • One 5.0 mm Phillips screw

    • Five 1.9 mm Philips screws.

    • One 2.5 mm Phillips screw.

On A1237, the yellow screw is a bit longer then the two orange ones.

Peterdk - Yanıt

I have replaced several Logic boards at this point on the A1304 model, and realized that I did not need to remove the heatsink (Steps 14 through 17). You need to remove the screws around the fan, and disconnect the microphone cable (step 19). Of course if your replacement logic board doesn't include a heatsink, you need to take it off.

Steerpike - Yanıt

  • Lift the processor clamp off the heat sink.

Yorum Ekle

  • Deroute the microphone cable away from the channel in the fan.

Yorum Ekle

  • Lift the heat sink up off the logic board.

  • Be mindful of the microphone cable when lifting the heat sink, as it can get tangled on the top edge of the fan.

  • When you mount the heat sink back onto the logic board, be sure to apply a new layer of thermal paste. We have a guide that makes replacing the thermal paste easy.

I removed the fan at this point as well. Disconnect the small connector from the fan to the logic board and lift out the fan. Good time to blow off the dust!

Andrea Wang - Yanıt

  • Use a spudger to pry the audio cable connector up off the logic board.

Yorum Ekle

  • If present, remove the small piece of black tape covering the microphone cable connector.

  • Disconnect the microphone cable by pulling its connector straight away from the socket on the logic board.

Yorum Ekle

  • Remove the two small Phillips screws securing the logic board bracket to the upper case.

  • Lift the logic board bracket out of the upper case.

Yorum Ekle

  • Use a spudger to pry the AirPort/Bluetooth and trackpad control cable connectors up off the logic board.

Yorum Ekle

  • Disconnect the DC-In cable by pulling its connector straight away from the socket on the logic board.

Yorum Ekle

  • Remove the small Phillips screw securing the display data cable ground loop to the upper case.

  • Disconnect the display data cable by pulling its connector straight away from the socket on the logic board.

Yorum Ekle

  • Remove the three Phillips screws securing the logic board to the upper case.

Yorum Ekle

  • Lift the logic board out of the upper case.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

47 başka kişi bu kılavuzu tamamladı.

4 Yorum

nice its very helpful for each other.

Rjames Tabuzo - Yanıt

I currently have a 1.6ghz A1237 Original Macbook Air, and I was wondering if the logicboard is interchangeable with the late 2008 model A1304. I hope someone can answer this for me. I want to swap out the logic board for A1304.

ric2081263 - Yanıt

I have the same question too. Who can help me because I want to upgrade to El Capitan instead of Lion

Tom Xu -

great work and helpful!

frank.haubold - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 23

Son 7 Gün: 176

Son 30 Gün: 954

Her zaman: 111,871