Menü

Ayarlarınız

Nintendo Switch Exterior Power and Volume Button Replacement

Yazan: Blake Klein
  • Yorumlar: 19
  • Favoriler: 0
  • Tamamlanma: 2

Zorluk

Orta

Adımlar

19

Gerekli Süre

45 dakika - 2 saat

Bölümler

7

İşaretler

0

Giriş

Follow this guide to replace the rubber conductive button pad and or exterior power and volume buttons.

When reinstalling, attach the exterior plastic buttons to the rubber conductive pad and insert them together into the device.

  1. Remove the four 6.3mm Tri-point Y00 screws from the rear panel.

    • Remove the four 6.3mm Tri-point Y00 screws from the rear panel.

    Düzenle

  2. Remove the single 6.1mm JIS #000 screw from underneath the kickstand.

    • Remove the single 6.1mm JIS #000 screw from underneath the kickstand.

    Düzenle

  3. Remove the two 2.7mm JIS #000 screws from the bottom of the device.

    • Remove the two 2.7mm JIS #000 screws from the bottom of the device.

    Düzenle

  4. Remove the single 2.7mm JIS #000 screw from the top of the device.

    • Remove the single 2.7mm JIS #000 screw from the top of the device.

    Düzenle

  5. Remove the single 3.8mm JIS #0 screw from the right Joy-Con rail. Remove the single 3.8mm JIS #0 screw from the left Joy-Con rail.

    • Remove the single 3.8mm JIS #0 screw from the right Joy-Con rail.

    • Remove the single 3.8mm JIS #0 screw from the left Joy-Con rail.

    Düzenle

  6. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device.

    • Pull the rear panel up and off of the device.

    Düzenle

  7. Remove the six 3.1mm JIS #000 screws from the shield plate.

    • Remove the six 3.1mm JIS #000 screws from the shield plate.

    Düzenle

  9. Remove the shield plate from the device. A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro. A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro.

    • Remove the shield plate from the device.

    • A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro.

    Düzenle

  10. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.

    • Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.

    Düzenle

  11. Remove the three 3.1mm JIS #000 screws from the heatsink.

    • Remove the three 3.1mm JIS #000 screws from the heatsink.

    Düzenle

  12. Pull the heatsink up 45 degrees and rotate it to the right to remove. Pull the heatsink up 45 degrees and rotate it to the right to remove. Pull the heatsink up 45 degrees and rotate it to the right to remove.

    • Pull the heatsink up 45 degrees and rotate it to the right to remove.

    Düzenle

  13. Remove the two 4.8mm JIS #000 screws from the fan.

    • Remove the two 4.8mm JIS #000 screws from the fan.

    Düzenle

  14. Use a spudger to flip up the small gray locking flap on the fan ZIF connector. Use a spudger to flip up the small gray locking flap on the fan ZIF connector.

    • Use a spudger to flip up the small gray locking flap on the fan ZIF connector.

    Düzenle

  15. Lift the left side of the fan out of its recess and rotate it 15 degrees towards you. Pull the fan out and away from you to unhook it from the rubber grommet. Pull the fan out and away from you to unhook it from the rubber grommet.

    • Lift the left side of the fan out of its recess and rotate it 15 degrees towards you.

    • Pull the fan out and away from you to unhook it from the rubber grommet.

    Düzenle

  16. Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector. Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector.

    • Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector.

    Düzenle

  17. Use the flat end of a spudger to pry up the tapped down power/volume ribbon cable.

    • Use the flat end of a spudger to pry up the tapped down power/volume ribbon cable.

    Düzenle

  18. Remove the power/volume board with a pair of blunt nose tweezers. Remove the power/volume board with a pair of blunt nose tweezers.

    • Remove the power/volume board with a pair of blunt nose tweezers.

    Düzenle

  19. Pull the rubber conductive pad out with a pair of blunt nose tweezers.

    • Pull the rubber conductive pad out with a pair of blunt nose tweezers.

    Düzenle

  20. Pull the power and volume buttons out with a pair of blunt nose tweezers. Pull the power and volume buttons out with a pair of blunt nose tweezers.

    • Pull the power and volume buttons out with a pair of blunt nose tweezers.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

Blake Klein

Üyelik tarihi: 29-01-2017

47.482 İtibar

48 adet Kılavuz yazıldı

Rozetler: 43

+40 tane daha rozet

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 4

Son 7 gün: 23

Son 30 gün: 96

Her zaman: 1,084