Öğrenci Katkılı Viki
Bu vikiyi, eğitim programımızdan harika bir öğrenci ekibi yaptı.
Headphones Won't Charge
Not seeing the LED light on Skullcandy Crusher Wireless indicates headphones are charging.
Charging Port Is Clogged Or Damaged
Check to see if there is any debris on the inside or if any debris is blocking the charging port on the side of the headphones. Inspect if the charging port is damaged and determine if it needs to be replaced. Use the flashlight on your phone to see a charging USB port at different angles.
Charging Cable Is Not Securely Inserted
Check if the charging cable is securely inserted on both sides (the USB charging port and the headphones USB port). You can look at the gap between cable and headphones, make sure to compare different sides.
Incorrect Power Adapter For Headphones
Make sure you are using the recommended charging cable and power adapter. It does not exceed 18-Watts (5 Volts/3.6 amps). Use the sensitivity of your fingers to locate the label of the power adapter.
Device Won't Turn On
There is no LED light indicating that the power is on, after pressing the main function button (circular button located on the right side) on your headphones.
Incorrect Power-On Procedure
- Hold the main function button down for 3 seconds
- LED (located on top of the volume up button) will flash purple to indicate that the device is powering on
- LED blinking blue indicates that the device is paired
- LED blinking red indicates that the device is not paired
Headphones Battery Is Discharged
Please connect the headphones to the charging block with a USB cable for at least 3 minutes. Try charging any device other than the headphones to make sure the charging is working. You may need to replace the battery.
Headphones Won't Connect With Other The Devices
You're having trouble pairing your Skullcandy Crusher Wireless Headphones with your device.
Incorrect Error Handling Of Bluetooth Connection
Fatal System Error Of Headphones Firmware
- Remove your Crusher Wireless headphones from your device’s paired list. And turn off Bluetooth mode on your device.
- Press and hold the "+" and "-" buttons. This will clear the pairing history on your Crusher Wireless.
- A voice prompt will say “Disconnected”, the headphones will go into pairing mode, and a voice prompt will say “Pairing”. If the headphones do not automatically go into pairing mode, press and hold the center button until the voice prompt says “Pairing”.
- Then, turn on your device’s Bluetooth and look for “Crusher” in your list of available Bluetooth devices. For Android devices: Click “+ Pair New Device” and select “Venue” to pair your headphones to your device.
- After selecting “Crusher”, accept any “Pair” or “OK” prompts that appear on your screen. When pairing is complete, a voice prompt will say “connected.”
Folding Of The Headphones Doesn't Work Properly
Folding the ear cups/pads on the headphones is not possible or difficult due to damage of the plastic joint of the headphones.
Broken Plastic Joint Of The Folding Hinge
If the headset has a broken folding hinge that might need a replacement. Check your headphones and try to find any cracks in the folding hinge. Check out our guide on replacing headphones folding hinges.
Product Defect
Occasionally, users may receive a product whose characteristics preclude the use of the foldable feature of the headphones for which it was designed and manufactured. Check out our guide on replacing headphones folding hinges.
Sound Works Only On One Side
Sound plays only on one headphones speaker of your Skullcandy Crusher Wireless.
Headphones Are Out Of Range Of Bluetooth
You may be able to listen up to 30 ft. (10 m) away from your paired device, though your connection experience may vary based on your environment. Signal reception is very standard and the quality of the sound will be good in 30 ft. range, but when you do finally reach the edge of their range it drops drastically.
Audio Port On The Headset Is Damaged
If the headset is still not transmitting audio well, the audio port may be damaged on the headset. Check out our guide on replacing the 3.5mm audio jack.
Charging Port Clogged On Headphones
Check to make sure that all the cables are properly connected between the headset and the device that audio is being played from. If there is debris in the sockets, clean them out using compressed air. Reconnect the cables and test the headset again. Check out our guide on replacing the 3.5mm audio jack.
Fatal System Error Of Headphones Firmware
Press the volume up and volume down buttons for at least 3 seconds. Please, release the buttons after you hear two beeps. You can follow the steps listed above to pair them again (read Reset Bluetooth Connection for the Headphones section).
Also, you can try to them off for a couple of minutes and then turn them back on. If you can still not pair them with your device, restart your device.
Low Bass Level Of Headphones
You're having a low bass sound playing on your Skullcandy Crusher Wireless.
Bass Control Headphone Slider Was Set To Low
- You can locate a slider that is used to adjust the enhanced haptic bass level on the back of the left ear cup.
- By sliding it to the bottom you will deactivate the bass enhancement and by sliding it up you will increase its effect.
- The slider allows you to fine-tune the bass level with fluid accuracy, due to no notches or steps in the slider so it moves smoothly up and down.
*Note: Max volume output is very high with the haptic bass feature disabled.
Audio Port On The Headset Is Damaged
If the headset is still not transmitting audio well, the audio port may be damaged on the headset. Check out our guide on replacing the 3.5mm audio jack.
Audio Cable Is Not Securely Inserted
Check if the audio cable is securely inserted on both sides: headphones and audio device. Check out our guide on replacing the 3.5mm audio jack.
59 Yorum
Mis audífonos de un momento a otro no enciende y tampoco cargan
elmicky14 - Yanıt
Me paso lo mismo, encontrarse alguna solución? Tienen reparación?
Ambar Escobar España -
Encontraste alguna solución?
Tachy Carlos Calderon -
Tengo un asunto con mis skull candy, a veces se desactivan los bajos de la nada y a los días funcionan nuevamente pero no sé cuál será el motivo
herminio.cardona - Yanıt
Haz logrado encontrar una solucion?
KhazZ -
Si también me paso eso pero abra alguna solución yo quise ser mi garantía válida pero al parecer la marca de Mexico no contesta por ningún motivo fui a la ciudad y al momento de llegar a la oficina descubrí que se avían cambiado sin saber a donde se fueron
Juan Carlos Paz Duran -
Es porque el nivel de volumen esta bajo. El regulador de volumen actua a partir de un de determinado volumen. Subele un poco.
alvaro rosas -
mi crusher no se conectan a ningún dispositivo, ya los reinicie y aun no se conectan
joe Monte - Yanıt
Hola mis audífonos tampoco se conectan, de igual manera los reinicie pero sigue sin querer.
Pudiste solucionarlo ? Me dice que el pin no es correcto
Zahira David -
Hola lograron resolver el problema?
Mjmjmjm -
Lograste solucionar el problema?
Eduardo Yael Victoria Flores -
Tengo unos crusher evo y no se conectan a ningún dispositivo, ya intente borrar todos los dispositivos conectados, emparejarlo nuevamente, pero aun nada, alguien me podría ayudar por favor?
Alberto Diosdado - Yanıt
Encontraste la solución?
Eduardo Yael Victoria Flores -
Tenia tiempo sin usar mis Skullcandy Crusher Wireless, entonces los puse a cargar con la energia de mi laptop (como siempre lo habia echo) pero luego de unos segundos de encender el LED rojo indicando que se estaban cargando, éste se apagaba, los desconecte y conecté varias veces, pero sucedia lo mismo, en momentos duraba un rato mas largo con el LED encendido, hasta que despues de varios intentos el LED cambió a verde indicando carga completa, comencé a usarlos con normalidad, pero despues de un tiempo escuchando musica estos se apagaban de la nada (no indicaban bateria baja ni nada), tenia que volverlos a encender, ya van van varias veces que sucede lo mismo, duran un rato funconando bien y de repente se pagan solos, estan en excelente estado, no los he utilizado con mucha frecuencia desde hace año y medio que los compré.
Víctor Hugo Velázquez Torres - Yanıt
No puedo conectarlos a ningún dispositivo!!
Benito camelo - Yanıt
Pudiste solucionarlo?
Iker CG -
hola, mis audifonos se pueden conectar a Bluetooth pero una vez conectados y pongo música se escucha de muy baja calidad el audio. Además, la luz azul que se queda encendida se queda parpadeando
Jose Luis Gonzalez García - Yanıt
Hola buen dia; tengo un problema con mis crusher, cuando reproduzco una canción se pierde la intensidad del sonido del lado derecho en ese instante cuando recargo o doy un recargon con mis dedos sobre la parte derecha, se empareja la calidad del sonido con el lado izquierdo, como si hubiese un falso contacto, ¿que podría ser?
Arturo Cuevas - Yanıt
The volume on my headphones only plays half as loud as they used to.
Fredrick Hostler - Yanıt
A mí también me.paso lo mismo y no.se que hacer
fer juarez - Yanıt
the base in my headphones won’t work and more I’ve tried to fix it and nothing is working pls help me
Rena Mcclanahan - Yanıt
¿Que debo hacer si perdí la caja de carga de los auriculares Bluetooth?
Cristina Mucha - Yanıt
Yo intenté reiniciar con los audífonos prendidos apreté el botón de encendido y el de bajar volumen entonces se quedó la luz morada encendida y no se apaga ahora aparece en mi lista de Bluetooth pero no lo empareja que puedo hacer???
Killia 1979 - Yanıt
It says I need a PIN code to connect my headphones, where do I find one?
x-_Petra.x. Pinkbeach_-x - Yanıt
my brand new crushers won't turn on. i have charged them with chargers that 100% work and they connected once the day i got them but died a few minutes after. when i plug them in a flashing green and yellow light appears. why?
kylie chandler - Yanıt
Is it possible to pair multiple devices to your headphones? Like obviously turn off your Bluetooth when trying to pair it with the other one. But I am kinda tired of having to make it forget the pairing and then switching over and over again.
Hina - Yanıt
Yo le dejé precionado volumen+ y botón del medio y encendió un foco rojo, después de eso, no volvió a conectar
Angel Gabriel Flores Cervantes - Yanıt
Mis audífonos se desconectan de repente y se vuelven a conectar muchísimas veces hasta el punto de no poder usarlos pero pasa muy seguido y después funcionan bien unos dias y vuelve a pasar, alguna solución?
Ricardo Aguilar Galaz - Yanıt
Tengo un inconveniente. No sé desde cuándo pero de la nada cuando me saco e audífono derecho vibra y hace un ruido que calma cuando me lo vuelvo a poner en la oreja. Pero siento que solo ese audífono suena levemente más bajo ó comprimido que el audífono izquierdo que no vibra.
Mel Bruce Melendez Vega - Yanıt
the bass in the right earphone doesn't work anymore. is there anyone that could tell me how to fix it?
Pulverizer 31 - Yanıt
Mis skullcandy crusher prende una luz verde pero no pasa nada ni prenden ya no se escucha ni empareja
alan garcia - Yanıt
Another possibility is that setting where your headphones might actually be too big for it and cause it to be loose applying a little bit of tape on the inside of the case can actually help hold it in the right position so you get into the position and then put the piece of tape in so that it sits properly connected to the pens
Anastasia Butler - Yanıt
Mis audífonos Skullcandy cargan pero se queda prendida una luz verde solo funcionan con cable pero con Bluetooth no funcionan pq no quieren encender
Javier ZFX NATION - Yanıt
Me pasa lo mismo pero si prenden nomás que no se conectan
Iker CG -
Mis audífonos ya no se conectan por Bluetooth pero con el cable auxiliar funcionan muy bien alguien sabe la solución?
Iker CG - Yanıt
Hola, me pasa lo mismo hace 2 semanas que compré los míos y ahora no se conectan.
¿Encontraste solución?
Civancg -
Pregunta por qué al usar el micrófono es decir cuando estoy en llamada se reduce mucho la calidad de sonido
Braulio Perez - Yanıt
I am having a weird problem where if I put the bass slider to 0 (the bottom) the right earcup starts playing full bass while the left one has no bass
Otherwise the bass slider works just fine and there are no other problems
Yojimon - Yanıt
Buenas noches, mis audifonos Crusher Evo dejaron de vincularse a cualquier dispositivo, alguien tiene informacion al repecto?
Dhamar Garcia Zepeda - Yanıt
Hola a mi me pasaba lo mismo y lo único que hize fue presionar el botón de apagar estando encendidos los audífonos hasta que se apagaran y así me volvieron a funcionar
Iker CG -
mis audífonos solo carga uno y el otro no a veces solo prende azul pero no aparece en la App aparece apagado ya los he dejado conectados o los limpie pero el izquierdo no carga el derecho si pero el otro no
Izzy - Yanıt
Mis audífonos no encienden pero se mantiene la luz verde encendida, primero fue roja los cargue y ya no quisieron prender, espere a que se descarguen de nueva cuenta y al volverlos a cargar y al conectar era roja la Liz después de un rato cambio a verde pero siguen sin encender, si los uso con el cable funcionan bien
Iris Xiomara Ortega Gonzalez - Yanıt
Mis skulcandy se desconcetan al salir a la calle
piero palacios - Yanıt
ayuda por favorrr mis skull candy dejaron de sonar los sub woofeeer, lo reincie y todo suena y luego. no un ayudita 😞
Saurom Erick - Yanıt
No sé puede vincular con el dispositivo ya que aparece clave o pin incorrecto
David Alminagorta Bustamante - Yanıt
Para poder conectar nuevamente los audífonos a mi me funciono presionar "+" y "-" unos 10 segundos hasta que los audífonos se apaguen y al volver a encender los ya me dejo vincularlos nuevamente
Atsel Rc - Yanıt
Eres un capoooo, intente de todo y nada, hasta que me metí a investigar más y mire que varias personas tenían el mismo problema de vincular, después miré tu comentario y me dio soluciónnn, Gracias brou🫡
Sanchezz X7 -
Funciona lo dicho
Josafat (Duck) -
Funcionooo!!! Muchas gracias meses buscando solución
Eduardo Yael Victoria Flores -
Mis skull candy crusher Evo dejaron de cargar y parpadea una luz roja cuando los conecto y si precio no el botón de encendido parpadea una luz verde
a.najerayeverino - Yanıt
A veces tiene interferencia en la música
deyvi milan corpuna gamarra - Yanıt
Es como un sonido que la música estaría como problemas, breve con varias aplicaciones y está igual
deyvi milan corpuna gamarra - Yanıt
Mis Skullcandy crusher Evo no quieren conectarse por Bluetooth alguna solución, ya probé todos los pasos y ya lo reinicie y no quiere hacer nada
Juan mecánico - Yanıt
A los míos les pasa igual, encontraste solución?
Civancg -
Mis audífonos dice error cuando encienden y cuando intento vincularlos
Millin - Yanıt
Mis crusher evo dicen error cuando los enciendo o trato de vincularlos
Millin - Yanıt
Como soluciono el problema de Error Fatal del Sistema de Firmware, sí ya intenté reiniciarlos. Y siguen sin conectarse a ningún dispositivo por Bluetooth.
Yahir - Yanıt
Mis audífonos los pongo a cargar u nada más esta en color ambar y cuando los quiero usar y los quiero prender aparece de nuevo el color ambar
Amdor - Yanıt
no puedo conectar mis skullcandy crusher evo a la aplicación....
no tienes una solución? gracias...
Jorge Valencia - Yanıt