Mac mini Late 2018 Memory (RAM) Replacement

Rod Bland ve 9 diğer katkıda bulunanlar

En son July 2, 2024 tarihinde güncellendi

20 - 40 dakika

Orta

Öne Çıkan Kılavuzlar

Giriş

1. adıma git

Learn how to upgrade or replace the memory in your 2018 Mac mini with this RAM replacement guide. The mini can support up to 64 GB of RAM, using any combination of 8 GB, 16 GB, or 32 GB DDR4-2666 SODIMM RAM modules.

Neye ihtiyacın var

Tamir Seti

Bu kit, bu kılavuzu tamamlamak için gereken tüm parçaları ve araçları içerir.

Mac mini Late 2018 Memory Maxxer RAM Upgrade Kit

Parçalar

PC4‑21300 16 GB RAM Chip
Sale price $89.99

Aletler

Daha fazlasını göster…

Videoya Genel Bakış

Adım 1 Bottom Cover

Mac mini Late 2018 Memory (RAM) Replacement, Bottom Cover: adım 1, 1 resimden 1.

Power off and unplug your Mac mini before you begin.
Use an opening tool to pry the bottom cover up off of the Mac mini.

Düzenle

Adım 2

Lift and remove the bottom cover.
To reinstall the cover:
Align it carefully so that the words "Mac mini" can be read when the ports are facing you.
Then, press down on the cover to snap its three hidden clips into place.

Düzenle

Adım 3 Antenna Plate

Mac mini Late 2018 Memory (RAM) Replacement, Antenna Plate: adım 3, 1 resimden 1.

Bu adımda kullanılan alet:

Magnetic Project Mat

$19.95

Sepete Ekle

Remove six TR6 Torx security screws securing the antenna plate, of the following lengths:
Three 4.1 mm shoulder screws
Three 1.8 mm screws
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your Mac.

Düzenle

Adım 4

Do not completely remove the antenna plate; it is still connected to the Mac mini by an antenna cable.
With the Mac mini's ports facing you, carefully lift the antenna plate and slide it about an inch to the right.

Düzenle

Adım 5

Use a T6 Torx driver to remove the 2.8 mm screw securing the antenna cable to the Mac mini's logic board.

Düzenle

Adım 6

Mac mini Late 2018 Memory (RAM) Replacement: adım 6, 3 resimden 3.

Bu adımda kullanılan alet:

Tweezers

$4.99

Sepete Ekle

The antenna cable connector and socket are fragile.
Use the point of a spudger or fine tweezers to gently pry the antenna cable connector straight up off its socket on the logic board.
To reconnect the cable, use tweezers to position it carefully over its socket on the logic board, and then press it straight down until it snaps into place.
If you need more slack in the cable, you can temporarily pry it from the clips securing it to the antenna plate.

Düzenle

Adım 7

Remove the antenna plate from the Mac mini.

Düzenle

Adım 8 Fan

Mac mini Late 2018 Memory (RAM) Replacement, Fan: adım 8, 2 resimden 1.

Mac mini Late 2018 Memory (RAM) Replacement, Fan: adım 8, 2 resimden 2.

Use a T6 Torx driver to remove the four 7.2 mm screws securing the fan:
Two screws securing the fan to the logic board
Two screws with rubber shoulders securing the fan to the exhaust vent
Rubber grommets secure these screws to the fan, so they may not come out completely. Just make sure they are fully loosened.

Düzenle

Adım 9

Don't try to remove the fan completely in this step—just lift it so you can access the cable underneath.
Lift the fan from the flat edge where it meets the exhaust vent, being careful not to strain the fan cable underneath.

Düzenle

Adım 10

Grasp the fan cable by all six wires and gently lift to unplug it from the logic board.
If the cable won't disconnect, don't force it, or you may pull the socket off the board. Try holding the socket down with your thumb, then pinch the cable close to the socket with your index finger and gently lift.

Düzenle

Adım 11

Remove the fan.

Düzenle

Adım 12 Logic Board Assembly

Mac mini Late 2018 Memory (RAM) Replacement, Logic Board Assembly: adım 12, 1 resimden 1.

Grasp the power supply cable and lift to disconnect it from the logic board, wiggling as needed to loosen it up.

Düzenle

Adım 13

Carefully lift the connector for the LED indicator light straight up to disconnect it from its socket on the logic board.
Take care not to pry under the socket, or you may break it off the board.

Düzenle

Adım 14

Use a T10 Torx driver to remove the two 7.5 mm screws securing the logic board.

Düzenle

Adım 15

Mac mini Late 2018 Memory (RAM) Replacement: adım 15, 3 resimden 3.

In this step, you'll push the logic board free from the clips holding it to the frame. Push only where directed or you may damage the fragile cooling fins.
Place a thumb at each end of the exhaust vent, over the fan screw holes.
Push firmly in the direction of the ports until the logic board unclips and begins to slide out of the Mac mini.

Düzenle

Adım 16

Slide the logic board out of the case.
When reinstalling the logic board, make sure to hold the thin LED indicator light cable out of the way so it doesn't get damaged.

Düzenle

Adım 17 RAM

Mac mini Late 2018 Memory (RAM) Replacement, RAM: adım 17, 1 resimden 1.

Use a T5 Torx driver to remove the four 2.8 mm screws securing the RAM shield.

Düzenle

Adım 18

Lift the RAM shield and slide it off of the RAM assembly.

Düzenle

Adım 19

Two clips secure each RAM module in place, one on each side. Using your fingers, spread the clips away from the RAM module.
When released, the RAM modules will pop up at a slight angle.

Düzenle

Adım 20

Slide each RAM module straight out to remove it.
When handling the RAM modules, touch only the outside edges. Take care not to touch the gold-colored contact points along the bottom edge.

Düzenle

Adım 21

Mac mini Late 2018 Memory (RAM) Replacement: adım 21, 3 resimden 3.

To install new RAM modules:
Make sure the module is oriented correctly and the notch on the bottom is aligned, and then slide it in at about the same angle as you took it out. Press evenly until the gold contacts are no longer visible.
Repeat for the second module.

Düzenle

Adım 22

Mac mini Late 2018 Memory (RAM) Replacement: adım 22, 3 resimden 3.

Finally, press the top edge of each RAM module to swing it down toward the logic board until the retaining clips on each side snap into place.
If the rubber guards interfere with the clips, spread the rubber guards away from the RAM with one hand and use the other to angle the RAM modules into place. Then, release the guards.
Check the clips and make sure both modules are fully seated and secure.